Arnica ASPIRON BORA 4000 Manuel d'utilisation - Page 7
Parcourez en ligne ou téléchargez le pdf Manuel d'utilisation pour {nom_de_la_catégorie} Arnica ASPIRON BORA 4000. Arnica ASPIRON BORA 4000 12 pages. Dry vacuum cleaner with water filter
Également pour Arnica ASPIRON BORA 4000 : Manuel d'utilisation (8 pages), Manuel d'instructions (8 pages)
Imprimer la page
than 60 oC, as this will cause a serious explosion and fire hazard! The
appliance must not be used near flammable substances and must
not be used to clean up health endangering dust.
Warning: Only perform dry vacuuming with your vacuum cleaner.
II. GENERAL DESCRIPTION
Main parts of the appliance are shown as follows (Figure 1)
A. MOTOR UNIT
This group contains motor, switch and operating units on. Top of this
group, there is a HEPA FILTER which filters dust and other particles
from blowing air.
A1. ON-OFF switch
A2. Cord rewinder button
A3. Hepa Filter
A4. Hepa Filter housing cover
A5. Suction inlet
A6. Body handle
A7. Wheels
A8. Clamp housing
B. CONTAINER GROUP
Container Group is for collecting dust and dirty water. This group
placed on the Body group.
B1. Transparent Water tank
B2. Cover of the Transparent Water tank
B3. Handle of the Transparent Water tank
B4. Water Filter Body
B5. Water filter tube
C.THE HOSE GROUP
This group contains suction hose with hand grip and suction tubes.
Suction nose is connected to container group by inserting the suction
hose into the suction inlet. Suction tubes are connected to hand
grip if necessary. Handgrip contains a manual sliding for regulating
suction power. Hose group can be placed onto the motor unit by the
help of hanger.
C1. The elastic suction hose
C2. Telescopic pipe
C3. Main brush
C4.Turbo brush
D. ACCESSORIES GROUP
There are various accessories for different cleaning purposes.
D1 - Accessories Holder
D2 - Crevice Nozzle
D3 - Round Nozzle
D4 - Small Nozzle
D5 - Parfume
III. TECHNICAL SPECIFICATIONS
Model: BORA 4000
Voltage: 230V~, 50Hz
Power: 2400W Max.
Electrical Insulation class: II
Cord Length: 6m.
Used Life: 10 years
IV. PREPARING FOR USE
• ATTENTION – Do not insert the mains plug into the wall socket
until the appliance is completely ready for use.
* Lift the Reservoir Group and put aside by holding from its handle.
* Remove the water filter tube and Water Filter Body by pulling after
you open the reservoir cover.
* Check the parts and accessories in the Operating Manual with the
ones you take out of the Tank. Check whether they are missing or
damaged.
•If you will use your vacuum cleaner immediately, add water in
the Transparent Water Tank in accordance with the maximum level
(Maximum 1.2 liter) indicated on the Tank.
* Drop 2 or 3 drops of perfume supplied with your vacuum cleaner into
the water for providing your room's air smells good.
* Replace the Water Filter Body and water filter tube to their places in
the Transparent water tank. Replace the water tank Cover.
* Replace the Transparent Reservoir Group on the main Body tightly.
* In order to connect the Hose Group to the Main Body Group, place the
Vacuum Head of the Hose on to the Vacuum Head on the tank.
*WARNING: Do not ever vacuum wet floors or
water from sink. Only perform dry vacuuming with
your vacuum cleaner.
V. OPERATING THE APPLIANCE
* Perform the Assembly and Preparation for Use processes.
* Choose the most appropriate accessories for your purpose and affix
these accessories directly on the gun section or affix the Extension
tubes first and then accessories on their ends.
is
* For an effective cleaning, use the accessories as mentioned in the
following.
» Main brush for vacuuming carpets, rugs and hard grounds.
»Crevice nozzle for cleaning the dusts, chips and etc. at radiators,
drawers and etc. narrow sections.
» Directly the Extension Tube for cleaning soil, debris, chips, feathers and etc.
»The Small brush Accessories for cleaning racks, clothes, electronic
devices, lampshades, furniture, curtains and etc.
» Round brush for cleaning curtains or dusting.
» The hard ground brush for cleaning dust and etc. on the hard
grounds such as parquet.
• Plug in your vacuum cleaner and start it by pressing the On-Off
Button.
• After completing the vacuuming process, turn off your vacuum
cleaner by pressing the On-Off Button. Unplug your vacuum cleaner
and furl the cord by pressing Cord Spinning button. For some models,
for furling the cable, it will be sufficient to hold and pull the cord lightly.
This specification can vary in accordance with the model.
VI. CLEANING AND MAINTENANCE
* You have to unplug your device, before beginning any Cleaning or
Maintenance processes.
* After every use, empty the water in the Transparent Water Tank and
clean and dry the tank.
* Do not ever leave your vacuum cleaner with liquid and dirt in it for
hygienic purposes and extending the life of your vacuum cleaner.
* Pull and remove the Water Filter Body and the engine air inlet neck.
The Water Filter Body and the engine air inlet neck can be washed with
warm and soapy water or under tap water. Dry after you wash these
parts before replacing them.
The cleanness of hepa filter should be checked periodically.
*
Clean the filter if it is not clean. This filter loses its characteristics
after a certain usage period and requires replacing.
• Carry your vacuum cleaner by holding from its Body Handle.
•Just use original parts and accessories for efficient cleaning and
lifecycle and warranty of your device. Provide the accessories and parts
from the closest Authorized Service when it is required.
*WARNING: Only perform dry vacuuming with
your vacuum cleaner.
7