Cub Elecparts TIRE INSIGHT Manuel d'installation rapide - Page 2

Parcourez en ligne ou téléchargez le pdf Manuel d'installation rapide pour {nom_de_la_catégorie} Cub Elecparts TIRE INSIGHT. Cub Elecparts TIRE INSIGHT 2 pages. 4-wheel battery tpms system

Imprimer la page

Abnormal Warning Illustration

When the TPMS sensor transmits abnormal signal to the receiver, a warning symbol will

blink and "beep" as an audio alarm. The abnormal value is shown on the corresponding

tire on the receiver.

3.3 Recommend the Receiver Mounting Position

It's our recommendation to mount within 1/3 of the region right on the center of

dashboard, or the position which can receive the sensor signal well.

Note:

1.Recommended battery type: Alkaline E91, 1.5V, AA battery, The operating temperature

of regular alkaline battery is -18℃~55℃, higher temperatures will cause battery

leakage.

2.Power saving design: in order to decrease the consumption of receiver battery, the

receiver has a dormant design, to save the battery power consumption. When the

ignition is on, the receiver will be restarted automatically by shock.

3.If you finish setting and want to return back to tire pressure/tire temperature display

screen under any setting mode, please hold the

4.Setting Items

Hold

for 3~5 seconds to enter the setting mode, press

Function

Description

Unit

Tire pressure setting (4.1)

Tone

Volume setting (4.2)

SETTINGS

Tire pressure and temperature setting for front and rear tire (4.3)

LEARNING

TPMS sensor ID learning (4.4)

ROTATION

Tire position rotation (4.5)

4.1 Tire Pressure Unit Setting

Enter Unit setting mode, press

press

to choose the desired unit, press

SETTINGS

▲Tire pressure unit setting

4.2 Volume Setting

Hold

for 3~5 seconds to enter the SETTING mode. Press

setting. Press

and set the volume value, the value of the volume will blink, press

the

button to adjust the value between 1 and 5, where 1 is the lowest volume level

and 5 is the loudest. The value is fixed and will stop blinking after pressing

SETTINGS

▲Volume Setting

4.3 Tire Pressure Standard Value and Temperature Warning Value Setting

Hold

for 3~5 seconds to enter the SETTING mode. Press

standard value and temperature warning value setting. Press

pressure standard value, the value of the front wheel will blink, press the

adjust the value. The value is fixed and will stop blinking after pressing

value of the rear wheel will blink, press

will stop blinking after pressing

completed. Then it enters the tire temperature warning value setting; the setting

procedure is the same as the tire pressure setting.

SETTINGS

▲Front Wheel / Tire Pressure setting

SETTINGS

▲Front Wheel / Tire Temperature setting ▲Rear Wheel / Tire Temperature setting

Note: For the tire pressure standard value, please refer to the placard which be

attached to the side of the driver seat.

button for about 3 seconds

for the following functions:

to tire pressure unit, the unit will blink,

to complete the unit setting.

psi

Bar

once for volume

once for tire pressure

and set the tire

to adjust the value. The value is fixed and

. The pressure standard value setting is now

psi

SETTINGS

▲Rear Wheel / Tire Pressure setting

SETTINGS

●Warning of excessive low tire pressure indicates tire pressure has been leaked to 20%

or less of the tire pressure standard value set by the user, or ≦150 kPa (22psi).

●Warning of excessive high tire pressure indicates tire pressure has been risen to 50%

or more of the tire pressure standard value set by the user.

●Warning of excessive high tire temperature indicates tire temperature is higher than

tire temperature warning value set by the user.

●For example, if the tire pressure standard value is 31 psi, when tire pressure is

increased ≧47psi or decreased ≦25psi, the receiver will alarm.

●For example, if the tire temperature warning value is 80℃, when tire temperature is

increased ≧80℃, the receiver will alarm. When the tire temperature is below 0℃, it

will show "Lo" on the panel.

●If the environment temperature is too hot or cold, the tire pressure will vary accordingly.

Please go to the tire shop to inflate or deflate the tires to prevent an erroneous alarm.

4.4 ID Learn Setting

When replacing or installing a tire pressure monitoring sensor for a second time, the

receiver must learn the new tire pressure sensor ID. The setting procedure is below:

4.4.1 Hold the

button for 3 to 5 seconds, enter the setting mode.

4.4.2 Choose the "ID Learn" mode.

4.4.3 Press the

button, the digits will blink.

4.4.4 Deflate the tire, the receiver will beep when receiving the signal; the ID learn

setting is finished when the digits stops blinking.

4.4.5 Press the

button again, then do the learning procedure for the next tire.

4.4.6 Repeat the above procedures until completing the learning of the 4 tires, then

please press

▲ID LEARN setting

Note:

1. When learning the sensor IDs by pressure deflation, please proceed with fast

deflation to avoid unsuccessful ID learning

4.5 Tire Position Rotation Setting

When the wheel is switched, the sensor position would be different from original. You

should use ROTATION mode for tire position setting.

In ROTATION mode, 1 to 4 digits is showed on screen. Press

flash. Press

to adjust tire position. Press

▲ Rotation setting screen

button to

, then the

psi

the button to save the ID numbers.

LEARNING

to save when the setting is completed.

, then the digit will