ARO PE20 series Manuel de l'opérateur - Page 9

Parcourez en ligne ou téléchargez le pdf Manuel de l'opérateur pour {nom_de_la_catégorie} ARO PE20 series. ARO PE20 series 12 pages. 2 inch diaphragm pump 1:1 ratio (metallic)

ARO PE20 series Manuel de l'opérateur
Product discharged from exhaust outlet.
Check for diaphragm rupture.
y
Check tightness of (14) diaphragm screw.
y
Air bubbles in product discharge.
Check connections of suction plumbing.
y
Check "O" rings between intake manifold and inlet side
y
fluid caps.
Check tightness of (14) diaphragm screw.
y
Motor blows air or stalls.
Check (176) check valve for damage or wear.
y
Check for restrictions in valve / exhaust.
y
Dimensions shown are for reference only, they are displayed in inches and millimeters (mm).
L
G
Q
M
Dotted lines show optional
67263 mu er assembly.
A - see below
B - 24-3/4" (628.7 mm)
C - 10-1/16" (255.6 mm)
D - see below
E - 16-3/16" (411.2 mm)
I - Side Discharge Ports are not avaliable on PX20X-XSX-XB Models.
PX20X-XAX-XXX-BXXX
PX20X-XCX-XXX-BXXX
PX20X-AHX-XXX-BXXX
PX20X-BHX-XXX-BXXX
PX20X-ASX-XXX-BXXX
PX20X-BSX-XXX-BXXX
PX20X-FHX-XXX-BXXX
PX20X-FSX-XXX-BXXX
PX20X-XXX-XXX-BXXX (en)
TROUBLE SHOOTING

DIMENSIONAL DATA

P
E
F
L
H
J
Exhaust port 1-1/2 - 11-1/2 N.P.T.
DIMENSIONS
F - 12" (304.8 mm)
G - 26-1/4" (666.8 mm)
H - 9-1/16" (230.2 mm)
J - 10-1/16" (255.6 mm)
K - 9/16" (14.3 mm)
"A"
"D"
19-3/4" (501.7 mm)
1-7/8" (47.6 mm)
19-3/4" (501.7 mm)
1-7/8" (47.6 mm)
19-1/4" (488.7 mm)
2-1/2" (63.5 mm)
19-1/4" (488.7 mm)
2-1/2" (63.5 mm)
19-3/8" (492.1 mm)
2-1/2" (63.5 mm)
19-3/8" (492.1 mm)
2-1/2" (63.5 mm)
19-1/4" (488.7 mm)
2-1/2" (63.5 mm)
19-3/8" (492.1 mm)
2-1/2" (63.5 mm)
Figure 4
Low output volume, erratic flow or no flow.
Check air supply.
y
Check for plugged outlet hose.
y
Check for kinked (restrictive) outlet material hose.
y
Check for kinked (restrictive) or collapsed inlet material
y
hose.
Check for pump cavitation - suction pipe should be sized
y
at least as large as the inlet thread diameter of the pump
for proper flow if high viscosity fluids are being pumped.
Suction hose must be a non-collapsing type, capable of
pulling a high volume.
Check all joints on the inlet manifolds and suction con-
y
nections. These must be air tight.
Inspect the pump for solid objects lodged in the dia-
y
phragm chamber or the seat area.
S
(Material outlet)
(PX20X-AXX-XXX-BXXX)
(PX20X-FXX-XXX-BXXX)
(PX20X-BXX-XXX-BXXX)
B
N
( Bolt circle)
Air Inlet
3/4 - 14 NPTF - 1
B
R
D
D
S
(Material inlet)
(PX20X-FXX-XXX-BXXX)
L - see below
M - 5/8" (15.9 mm)
N - 4.834" (122.8 mm)
P - 21-5/8" (548 mm)
Q - 27-7/8" (708.0 mm)
"L"
2" (50.8 mm)
2" (50.8 mm)
2-3/32" (53.0 mm)
2-3/32" (53.0 mm)
2-3/32" (53.2 mm)
2-3/32" (53.2 mm)
3-1/4" (82.6 mm)
3-1/4" (82.6 mm)
Material outet
T
U
K
C
A
Material inlet
T
(PX20X-AXX-XXX-BXXX)
U
(PX20X-BXX-XXX-BXXX)
R - see below
S - 2" A.N.S.I. / DIN Flange
T - 2 - 11-1/2 N.P.T.F. - 1
U - Rp 2 (2 - 11 BSP, parallel)
"R"
12-15/16" (328.6 mm)
12-15/16" (328.6 mm)
13-9/16" (344.5 mm)
13-9/16" (344.5 mm)
13-9/16" (344.5 mm)
13-9/16" (344.5 mm)
13-9/16" (344.5 mm)
13-9/16" (344.5 mm)
Page 9 of 12