Acoustic Research AW791 Manuel d'installation et d'utilisation - Page 5

Parcourez en ligne ou téléchargez le pdf Manuel d'installation et d'utilisation pour {nom_de_la_catégorie} Acoustic Research AW791. Acoustic Research AW791 6 pages. Wireless surround sound headphones with dolby digital technology

Imprimer la page

1. Turn on the component you wish to listen to (DVD player, VCR, TV, or

another audio/video product).

2. Press the Input Select Switch (D) to choose the device you wish to listen to,

i.e., Digital 1, Digital 2, or Analog 3.

3. Press the Surround Sound ON/OFF Switch (A) to turn the effect ON or

OFF depending on the source material you wish to listen to. The virtual

Surround Sound should be on for all Dolby Digital or Dolby Pro Logic

encoded source material. All stereo music CDs, cassette tapes, or AM/FM

radio should be experienced with the virtual Surround Sound OFF.

See Processing Modes below.

4. Turn the headphones ON by pressing the ON/OFF/Tuning Control (M).

The headphones may take a few seconds to tune.

5. Put the headphones on your head.

6. Adjust the volume (L) to a comfortable listening level.

7. When finished, power down the headphones by depressing the

ON/OFF/Tuning Control (M) until the Power Indicator Light (K) is OFF.

Note: The headphones must be OFF for the batteries to charge properly.

Make sure the Power Indicator Light (K) is OFF before charging.

1. For multi-channel inputs (Dolby Digital inputs), the "virtual mode"

processing uses 5.1 channel Dolby Digital decoding then virtual

processing to create a 2 channel 3-D room equivalent output.

2. For multi-channel inputs (Dolby Digital inputs), the "stereo mode"

processing uses 5.1 channel Dolby Digital decoding/processing for any

number of channels to create a 2 channel equivalent output. If the multi-

channel input is stereo, then the 2 channel output is stereo (i.e., Dolby

Digital Stereo).

3. For Analog or PCM inputs, the "virtual mode" processing uses Dolby Pro

Logic decoding then virtual processing to create a 2 channel 3-D room

equivalent output.

4. For Analog or PCM inputs, the "stereo mode" processing uses direct

stereo decoding to create a 2 channel stereo output.

Note: This product does not decode DTS 5.1 encoded digital signals.

Listening

to the

Headphones

Processing

Modes

- 6 -

Troubleshooting

The following troubleshooting guide takes you through some of the most common issues

and solutions associated with the installation and/or operation of the Wireless Surround

Sound headphones.

Issue

Cause and Solution

No Sound

• Check that the AC Power Supply (O) is fully inserted into the wall outlet

and the barrel connector from the AC Power Supply (O) is firmly

connected to AC Input Jack (E). When the AC Power Supply (O) is

properly connected and providing power, the Surround Sound ON/OFF

Light (B) and Analog Input Indicator Light (C3) should be ON prior to

making any selections.

• Check that the headphones are turned "ON" and the red Power Indicator

Light (K) is brightly lit.

• Check that the Rechargeable Batteries (P) are firmly seated in the Battery

Compartment (H) following the polarity markings in the Battery

Compartment (H).

• Check that the audio source (DVD player, TV, VCR) is turned "ON" and

providing sound as it normally should.

• Check that the headphone Volume Control (L) is turned up.

• If the Surround Sound LED (B) is blinking, this indicates that the input is

DTS encoded. This product does not decode DTS 5.1 encoded digital

signals. Refer to your DVD, Satellite, or other manual to change the audio

mode from DTS output to Dolby Digital or PCM output.

Note: Usually you can select among PCM, Dolby Digital and DTS output

formats on DVD players and satellite receivers.

• Check that the component' s digital sampling rate output is 48K

samples/second or lower. This product does not support 96K

samples/second. Refer to the component's manual to change the audio

sampling rate output.

Distortion/Static

• Check that the headphone Tuning Indicator Light (N) is illuminated. If

not, push the ON/OFF/Tuning Control (M) to manually search for the

channel. If it does not lock quickly, change the Channel Select Switch (G)

to one of the other two channels.

• Check the batteries - they may be weakening.

• Confirm the batteries are "good." When batteries begin to weaken, there

can be static breakup. If necessary, recharge the batteries.

• Change the physical location of the transmitter. Locate it as high and free

of obstruction as possible. Avoid placing the transmitter directly on top of

a TV.

• Check that the Digital Coaxial Output from the DVD, satellite, etc., is

not connected to the Analog Audio Inputs (F3).

Sound from One

• Check the left/right balance control on the audio source.

Earpiece Only

• Check that the Tuning Indicator Light (N) is illuminated.

• Check the batteries – they may be weakening.

• Check that both Analog Audio Input Connectors (F3) are properly

connected, and that the audio source (VCR, TV, etc.) is equipped with

Stereo Analog Audio Output.

- 7 -