3DR LiveView Kit for GoPro Manuel de l'utilisateur - Page 2

Parcourez en ligne ou téléchargez le pdf Manuel de l'utilisateur pour {nom_de_la_catégorie} 3DR LiveView Kit for GoPro. 3DR LiveView Kit for GoPro 2 pages.

Imprimer la page

IRIS+ Mounting

Choose a position on the shell to mount the video transmitter, and

attach the second piece of velcro there. You can mount the transmitter

anywhere on the shell where it will not obstruct the propellers or interfere

with the battery door. We recommend placing it between the gimbal

interface place and the battery door; make sure to place it close enough

to the gimbal plate so that the battery door can fully open.

Locate the gimbal power cable on the underside of IRIS, and disconnect

the two red connectors. This is where you will connect the splitter cable

to power both the gimbal and the video transmitter off the flight battery.

IRIS: Disconnect gimbal power cable

Connect the splitter cable to both red connectors. The splitter cable

should now be connected to (1) the red connector on the gimbal power

cable, (2) the red connector on the IRIS power cable, and (3) the video

transmitter. Secure the two velcro strips together.

Monitor Assembly

Mounting bracket parts

To mount the monitor to the controller:

1 Place the elongated silver cap over the controller's neck strap

tachment. Then set the large spacer in the wide side opening and screw

in the smaller screw from the same side using a 2.5 mm hex key.

2 Rest the small spacer in the cap's adjescent chamber and lower the

curved bracket into line with the spacer. Secure these pieces by screwing

the flat-headed screw into the openings of the bracket and the spacer.

3 To mount the monitor to the controller, insert the larger black screw

into the hinge between the two silver parts. Adjust the monitor's angle by

screwing in the headless screw from the top of the bracket.

4 Add the black washer to the silver screw, and attach to the monitor

using the threaded insert in the bottom of the monitor. Screw on both

antennas to the top of the monitor.

(2.5 mm hex key)

Monitor assembly 1

(3 mm hex key)

Monitor assembly 3

Recommended placement of mounting

velcro on IRIS

Monitor assembly 2

Add antennas to

monitor.

Monitor assembly 4

IRIS, video transmitter, and gimbal:

complete wiring

X8+ Mounting

Attach the second piece of velcro in front of the Pixhawk where the video

transmitter can connect to both the power and video output cables.

Connect the red connector on the X8 to the larger red connector on

the splitter cable. (The splitter cable's smaller red connector will remain

unconnected.) Connect the X8's red, white, and black three-wire cable

to the transmitter with the black wire closest to the outside edge of

the transmitter. Secure the two velcro strips together. Either mounting

configuration shown below is acceptable.

Power cable

X8 and video transmitter: complete wiring

Operation

at-

Power the copter, controller, gimbal, and GoPro normally. Press and

hold the power button until you see a red light to turn on the monitor.

Monitor

Power

To see your video, make two adjustments to your monitor's settings:

1 Switch the band to E in the RF settings. To do this, open the main

menu by pressing the power button twice and scroll to the RF submenu

using the down arrow button. Press the M button to enter the RF settings,

press the M button again to highlight the Diversity band's letter selector,

and navigate to band E using the up and down arrow buttons. Press the

power button three times to exit all menus and save your settings.

2 Switch the monitor to channel 8 (+ and - buttons).

Video Transmitter Specs

5.8 GHz 200 mW wireless AV transmitter:

Transmitter frequency / channel amount:

5705-5945 MHz / 8 CH

Output power: 200 mW/33 dBm

Frequency control: Built-in frequency &

phase lock loop

AV input: analog AV signal input

Support

We're here to help.

online: 3dr.com/support

email: [email protected]

call: +1 (855) 982-2898 (toll free)

+1 (858) 225-1414 (direct)

Splitter

cable

IRIS LiveView complete assembly

Video output

cable

X8 and video transmitter: complete assembly

Mode

Down

Minus

Plus

ANT connector: RP-SMA

Power supply: DC 7-12 volts

Current supply: 850 mA

Size: 68*26*28 mm

Weight: 60 g (including antenna)

Gross weight: 85 g

Support line hours:

Mon-Fri 8 am to 5 pm PST