3dsimo MultiPro Mode d'emploi - Page 2
Parcourez en ligne ou téléchargez le pdf Mode d'emploi pour {nom_de_la_catégorie} 3dsimo MultiPro. 3dsimo MultiPro 2 pages. Multifunctional tool for workshops and households
Également pour 3dsimo MultiPro : Manuel de l'utilisateur (12 pages)
Imprimer la page
Burning attachment
After mounting the Burning attachment and
successful
completion
of
tutorial,
desired temperature of the tip (0-100%; 100%
≅450°C/842°F)
and
activate
heating
attachment by pressing front button.
Soldering attachment
After
mounting
the
Soldering
and successful completion of tutorial, choose
desired temperature of the tip (0-100%; 100%
≅450°C/842°F)
and
activate
heating
attachment by pressing front button.
6. Maintenance
3D drawing attachment
Make sure the filament is not deformed and
winded up too tightly
Before finishing your work with 3D drawing
attachment, ALWAYS fully pull out the filament,
to prevent possible damage to internal parts of
your device.
Cleaning the nozzle is possible using paper
towels when the nozzle is heated up to operating
temperature -WARNING- HOT!!!
Soldering and Burning attachment
Cleaning the attachment is possible using paper towels,
choose
never use sharp, hard or otherwise abrasive tools, tips have
special coating and such cleaning methods may lead to
of
the
unwanted behavior of the attachment.
Burning and soldering tips are consumables, and it is
possible to replace them with tips available on 3Dsimo
e-shop. Dismount the tip by unscrewing it counterclockwise.
Tightening of replacement tip has to be done clockwise,
attachment
finger tight only, without using any tools.
Foam cutting attachment
of
the
Cleaning of the resistance wire can be done using paper
towels.
In case of resistance wire breaking, always replace the
wire with new segment from supplied spool, or with wire
available at 3Dsimo e-shop.
7. Warning
Danger of burn injury – 3Dsimo attachments and it's parts
can reach temperature of up to 450°C (842°F), DO NOT
TOUCH the nozzle, resistance wire or the burning and
soldering tips few minutes after finishing work with the
attachment.
DO NOT dismout the 3D drawing attachment when the
filament is still inside the attachment, otherwise you might
damage internals of the device!
Avoid contact of 3Dsimo Multipro and it's parts with
flammable and volatile substances.
Warn your surroundings about high temperatures of
attachments.
Always let the attachments cool off before storing them in
the packaging, otherwise high temperatures may lead to
damage to the packaging and attachments.
Always use original 3Dsimo Inc. filaments and accessories.
Using unauthorised filaments and accessories may lead to
unrepairable damage to the device and it's attachments.
3Dsimo Inc. is not liable for damage caused by not folowing
User's manual.
This product and any of it's parts are not a toy, children have
to be under adult supervision while using this device.
Keep all the parts and accessories of 3Dsimo MultiPro dry,
avoid contact with fluids at any times while transporting
and/or storing 3Dsimo device.
Never take 3Dsimo MultiPro appart. In case of any failure
or unwanted behavior, contact our customer support:
Never use power adapter and power cable if any of it's
parts are damaged. Risk of injury by electricity.
Save this User's manual for later use.
3Dsimo Inc. is not responsible for any injury or damage
to property if 3Dsimo MultiPro or any of it's accessories
and attachments are used otherwise than is stated in
this user's manual.
8. Specifications
Adapter:
Input voltage: 100 - 240V AC, 50/60Hz
Output voltage: 12V, Output power: 24W
3Dsimo MultiPro:
Input voltage 12 - 24V, Input current 2A
Noise level:
21 - 30dB
9. Certificates
This device follows European Regulation for Registration,
Evaluation, Authorisation and Restriction of Chemicals
(REACH)
(Regulation
no.:1907/206/ES
parliament and European Council), and European
regulation for limiting usage of dangerous substances
in electronical devices (ROHS) (Regulation no.:2002/95/
ES of European parliament and European Council)
European safety regulations. This device is following
European safety regulations.
10. Warranty and customer support
This device includes 12 month warranty.
In case of any failure or misbehavior of this device, please
contact [email protected]
Original accessories and filaments are available here:
www.3dsimo.com/eshop
of
European