esera automation Multisensor Pro 11150 Manuel de l'utilisateur - Page 2
Parcourez en ligne ou téléchargez le pdf Manuel de l'utilisateur pour {nom_de_la_catégorie} esera automation Multisensor Pro 11150. esera automation Multisensor Pro 11150 5 pages. 1-wire sensor for temperature and air humidity w/auto-e-connect
Imprimer la page
3
Auto-E-Connect® Support
The ESERA Auto-E-Connect® 1-Wire Plug and Play system will be used for the
1-Wire Bus supported. This enables fully automatic configurations of 1-Wire sensors
and actuators on the 1-Wire bus. It is optimized for industrial applications and
enables significant added value beyond the sensor and chip data.
The Auto-E-Connect function automatically recognizes ESERA chips, sensors and actuators, starts suitable
libraries and outputs fully formatted data.
The Auto-E-Connect functionality will be available from mid-2020 via 1-Wire Controllers, 1-Wire Gateways and
1-Wire ECO from ESERA available.
Further information on ESERA Auto-E-Connect can be found on the ESERA website, ESERA Config-Tool 3, or in
the download area for this article in the ESERA Webshop.
4
Technical data
Function:
Temperature sensor:
Range of measuring temp.: -40°C to +60°C (sensor element: -40°C to +85°C)
Accuracy temperature:
Resolution:
Humidity sensor:
Range of measuring hum.: 0-100% rel. humidity
Accuracy humidity:
Data output:
Interface:
Connection:
1-Wire interface:
Operating voltage:
Current consumption:
5
Ambient conditions
Protection system:
Protection class:
Temperature, operation: -25°C to 70°C, (limitation by carrier system, sensor -40°C to +125°C)
Humidity:
Outer dimensions:
6
Conformity
EN 50090-2-2
EN 61000-4-2, ESD
EN 61000-4-3, HF
EN 61000-4-4, Burst
EN 61000-4-5, Surge
EN 61000-6-1, interference immunity
EN 61000-6-3, interference radiation
RoHS
7
Software / Control
The 1-Wire Multisensor Pro is being read out per 1-Wire commands for the DS2438 modules. The sensor is
supported by many systems such as ESERA Station, Loxone, IP-Symcon, OWFS, FHEM (Linux) or
microcontroller applications.
For ESERA 1-Wire Multisensors of the Pro series no elaborate formulas are necessary.
A sensor controller within the Multisensor takes over the preprocessing of all measured values and thereby
enormously simplifies the integration into 1-wire systems. The measured values are no longer dependent on
the operating voltage of a 1-Wire Multisensor.
The values measured by the sensor are assigned to the standard DS2438 module values as follows:
VDD = operating voltage (5V), TEMP = temperature, VAD = humidity, Xsense = no data output, fixed at 0.
All rights reserved. Reproduction as well as electronic duplication of this user guide, complete or in part, requires the written consent of
ESERA GmbH. Errors and technical modification subject to change. ESERA GmbH, ESERA-Automation 2020
www.esera.de
Multisensor for temperature and rel. humidity and air quality,
monitoring of operating voltage
Precise digital temperature sensor with 12 Bit measurement resolution
0,3° in the range of -10°C - 60°C (more accurate than the DS18B20 sensor)
12 Bit, 0,06°C/Bit depending on selected resolution
Capacitive digital humidity sensor with high accuracy
+/-3 % in the range of 10-85% rel. humidity
0-10V equates 0-100% rel. humidity, 0,1V = 1% rF
3 - wire connection (data, ground and 5V, parasitic operation not supported)
Push-in clamps for cable solid 0,2 to 2,5qmm or finely stranded 0.2 to 1,5qmm
For connection we recommend slotted screwdriver of the size 2,5x751-Wire
interface
Basis DS2438
5 V= (+10% / -20%)
approx. 2 mA
IP20
III
10 - 90% (non condensing)
71 x 71 x 32mm (LxWxH)
11150 V2.0 R1.0 Manual
Page 2 of 5