ClearCube C7130 Manuel de démarrage rapide

Parcourez en ligne ou téléchargez le pdf Manuel de démarrage rapide pour {nom_de_la_catégorie} ClearCube C7130. ClearCube C7130 2 pages. Auto-tune fails on certain eizo lcd displays
Également pour ClearCube C7130 : Document technique (2 pages), Document technique (1 pages), Document technique (1 pages)

Imprimer la page

C7130 C/Port

Notes

CAUTION: Do not attach the C7130

C/Port to a telephone jack or other

powered network connection. This will

permanently damage the C7130 C/Port. This

damage is not covered under the ClearCube

Technology limited warranty.

• Improper connection, mounting, or use of this

product could result in component failure or

undesired interference.

• Allow sufficient space around the C7130

for ventilation. Do not place the unit in any

enclosure that restricts airflow around the

device, or on top of any device that gener-

ates significant heat.

• To ensure regulatory compliance, use only the

power supply included in the shipping carton

with the C7130, or a ClearCube-approved

equivalent.

• Do not force a connector into its socket. Do

not connect to AC power until all other con-

nections are made, including the power

adapter.

• Do not connect or disconnect USB devices or

other peripherals during C/Port or Blade start-

up, or unpredictable results may occur.

ClearCube Technology

Quick Start Guide

The C7130 C/Port connects standard desktop peripherals to the user's

QSG_C7130_rev_B.fm — Enter your TB topic here

ClearCube PC Blade. When used with an R4300 Chassis, the C7130

provides automatic video tuning to deliver optimal display quality.

CONNECTIONS

1. Video Sharpness control

2. VGA video port

3. CPU link cable connector

4. Power supply connector

5. Audio line in

6. Audio line out

CAUTION: Do not plug a telephone cable or Ethernet cable into the

C7130.

4. Connect the C/Port power supply module to the power supply con-

nector, and then plug the power supply into the AC power socket. The

blue power indicator on the front of the C/Port will light.

5. Examine the Link Status Indicator LED on the front of the C/Port. It

should be green if connected to a PC Blade that is powered on.

If the LED is not green, verify that the link cable is connected to the

C7130, the Chassis has power, the PC Blade is turned on, and the cor-

rect link cable is plugged into the PC Blade.

6. Set the Blade to the desired resolution and scan rate. For best

results with an LCD monitor, set the monitor to its native resolution and

press its Auto-Adjust button.

A higher quality monitor will provide better video results.

Using the C7130 Blade Reset Button

To restart the Blade, press and hold the C7130 Blade Reset button for

at least two seconds to send a Reset signal to the Blade.

8834 Capital of Texas Hwy N

After unpacking the C7130 C/Port and

power supply, do the following:

1. Verify that the three color switches on

the bottom of the C7130 are set to the

positions marked F, and that the Video

Sharpness Control is set to the 12 o'clock

position. Adjust these controls if neces-

sary. See the diagram on the back of this

sheet.

2. Connect the desktop peripherals to the

C7130 as indicated, and then attach the

power connectors to the peripherals.

3. Connect the twisted-pair link cable

(CAT5 or similar) from the PC Blade to

the CPU connector on the C7130.

Austin, Texas 78759

voice 512 652 3500 www.clearcube.com

7. PS/2 keyboard port

8. PS/2 mouse port

9. USB 1.1 ports (2)

10. Blade Reset button

11. Power indicator

12. Link Status Indicator LED