Akiyama CDJ-MP100 Manuel d'instruction - Page 6

Parcourez en ligne ou téléchargez le pdf Manuel d'instruction pour {nom_de_la_catégorie} Akiyama CDJ-MP100. Akiyama CDJ-MP100 13 pages. Professional cd player

Imprimer la page

PART NAMES AND FUNCTIONS

REAR PANEL

20. PITCH RANGE

- This button changes the pitch value. The pitch

percentage can be changed between 4%, 8%, and 16%. 4% yields the

least amount of pitch manipulation and 16% will yield the most

amount of pitch manipulation. To adjust to the different values tap this

button. The LED above this button will indicate which pitch

percentage

mode is activated. The pitch values will immediately reflect the

amount of pitch being applied to a music source in the CD drive. The

pitch value is adjusted by sliding the PITCH SLIDER up and down.

21. PITCH ON/OFF BUTTON

function on and off. The pitch percentage value can be changed from

(+/-4%), (+/-8%) or (+/-16%). The PITCH SELECT LED will

indicate the maximum pitch value.

- This LED will glow when the pitch

22. PITCH LED

function is active.

23. PITCH RANGE LED

the selected pitch percentage mode. A flashing LED will indicate 4%

pitch manipulation, a solid glowing LED will indicate 16% pitch

LCD DISPLAY

1. TIME BAR INDICATOR -

defined in the TIME METER (M, S, &F). As with the TIME METER

this bar is also dependent on the selected time function TOTAL

REMAIN, REMAIN or ELAPSED. This bar will begin to flash when

15 seconds of a track remain and will begin to rap idly flash when

three seconds of a track remain. The flashing bar is a great visual

reminder a track is about to end. The flashing bar will function

regardless of which time mode the unit is in.

2. SINGLE INDICATOR -

mode, the unit will play a single and return to CUE mode. If the single

indicator is not displayed the unit is in continuous mode. In

continuous mode the drive will play through all the tracks on the disc.

3. TRACK INDICATOR -

track. The number displayed in the track indicator is a direct reference

to a track being selected a track in play, pause, or cue mode.

4. MINUTES METER -

remaining time in minutes. The display time will be indirect reference

to the current time mode.

5. SECONDS METER -

- This button is used to turn the pitch

- This LED serves as a visual reminder of

This bar visually details the time

This indicates the unit is in single play

This 3-digit indicator details a current

This meter will display the elapse, total, or

manipulation, and when the LED is off 8% pitch manipulation will be

applied to the PITCH SLIDER.

24. LINE OUT R & L

output signal. Use these jacks to send standard audio to a mixer or

receiver.

25. DIGITAL OUT

this connection to create near perfect copies of your disc to a Mini

disc, CD-R, or any other recording device with a digital input.

26. REMOTE START

fader start input. This enables the user to start the CD from the cue

point, using the mixer's cross or line fader, depending on the mixer.

27. POWER CONNECTOR

Only use the supplied polarized power cord. Use of any other power

may result in Sever damage to the unit. Be sure the local power

matches the unit's required power.

28. POWER SWITCH

remaining time in seconds. The display time will be indirect reference

to the current time mode.

6. FRAME METER -

frames. The displayed frames will be indirect reference to the current

time mode.

7. TOTAL REMAIN INDICATOR -

reference to the TIME METER. When the TOTAL REMAIN

indicator is displayed in the LCD, the time defined will refer to a disc's

total remaining time. The time mode is changed by tapping on TIME

button.

8. REMAIN INDICATOR -

the TIME METER. When the REMAIN indicator is displayed in the

LCD, the time defined will refer to a single track's remaining time.

The time mode is changed by tapping on TIME button.

9. PITCH METER -

applied to playback by the PITCH SLIDER. If the meter read zero

regardless of the PITCH SLIDER'S position, the PITCH function is

not activated.

c d j - m p 1 0 0

- These jacks send a left and right analog mono

- This jack sends a digital stereo out signal. Use

- Connects to any DJ mixer equipped with a

- This is the main power connection.

- This switch controls the unit's main power.

This meter will display the elapse, total, or

This indicator is in direct

This indicator is in direct reference to

This meter displays the pitch percentage being