ACOUSTIC SOLUTIONS SP150 Manuel - Page 15

Parcourez en ligne ou téléchargez le pdf Manuel pour {nom_de_la_catégorie} ACOUSTIC SOLUTIONS SP150. ACOUSTIC SOLUTIONS SP150 17 pages. Cd/hard drive audio jukebox

Imprimer la page

ADVANCED FUNCTIONS

OUTPUT LEVEL

��

1. The output signal level of the SP150 can be changed to

match the input sensitivity of the ampliﬁcation equipment it

is connected to.

2. The default output level setting of the SP150 is 27, this

equates to 280mV.

3. To alter this setting use the up/down arrow keys on the

remote control to select a level between 0 and 31.

4. Press OK to conﬁrm your selection, or after a time out

period of 30 seconds the SP150 will accept this new output

setting and revert back to the normal play menu.

5. The following table represents the respective output

senstivity levels for the output level numbers:

Volume setting table:

Volume 0

2mV

Volume 3

4mV

Volume 7

8mV

Volume 11

17mV

Volume 15

35mV

Volume 19

70mV

Volume 23

140mV

Volume 27

280mV

Volume 31

560mV

SOFTWARE REVISION NUMBER

It is possible to check the revision number of the software

loaded onto the SP150.

From the System menu when scrolling through options

you will see a screen similar to this:

��

CHECK DISK

The SP150 will allow some self diagnostics on the hard

drive. This may be necessarry if the SP150 malfunctions

or develops a problem.

From the System menu scroll down using the up/down

keys on the remote control until you see the check disk

screen:

��

Press the OK button on the remote control to initiate a

check of the harddrive

After the SP150 has checked the hard drive, if there is any

malfunction it will display a malfunction code.

Please consult your local dealer or ring the Acoustic

Solutions customer helpline for further information.

08712 307747 inside United Kingdom

+441327 340601 outside United Kindom

Please note that our customer helpline is open

Mon-Fri 09:00-16:30 (GMT) excluding National holidays.

UPGRADE

As software updates become available it is advisable to

install these.

Note: please ensure that you have registered your SP150

using the warranty card to ensure that you receive the

latest updates.

If it is necessary to update the operating software, this will

be introduced into the SP150 on a CD rom.

1. Press eject on the front panel (14), to open the CD

drawer.

2. Place the update CD into the drawer with the label

uppermost and press eject again.

3. The CD drawer will close load the CD, and it will

display that the CD is not an audio CD.

4. From the System menu select the "Upgrade" function

and press "OK" on the remote control (15).

5. The SP150 will then update the operating software

from the CD rom in the CD drawer.

6. The SP150 will then prompt you to reboot the system

for the new software to take effect. This will require the

power to be turned off, and then on again using the

power button on the front panel (8).

UPDATE CDDB

The SP150 uses the CDDB database to name CD's

which are played or stored on the hard drive.

Note: please ensure that you have registered your SP150

using the warranty card to ensure that you receive the

latest updates. These are free for the ﬁrst 12months.

It will be necessary to update the CDDB database to

ensure that the latest CD releases are recognised by the

SP150, and this will be introduced into the SP150 on a

CD rom.

1. Press eject on the front panel (14), to open the CD

drawer.

2. Place a CD into the drawer with the label uppermost

and press eject again.

3. The CD drawer will close load the CD, and it will

display that the CD is not an audio CD.

4. From the System menu select the "Update CDDB"

function and press "OK" on the remote control (15).

5. The SP150 will then update the database from the CD

page 15