Altox GSM-4 GPS Manuel d'utilisation - Page 4
Parcourez en ligne ou téléchargez le pdf Manuel d'utilisation pour {nom_de_la_catégorie} Altox GSM-4 GPS. Altox GSM-4 GPS 4 pages.
Imprimer la page
To request the account balance of the SIM card (by number from the BAL
setting) use SMS command «USSD». If you need to request data for another
phone number, add it in the command: «USSD:*XXX#».
Additional commands
Send USSD-request *XXX# using the module's SIM card
Send text message ХХХ from SIM card's number to NNN SMS:NNN:XXX
Request GSM stations data (MCC,MNC,LAC,CID)
Note: MCC, MNC, LAC and CID data allow to determine the location of the
vehicle on the map (using Google, Yandex services, etc.).
LAC and CID fields values are displayed in hexadecimal notation.
Settings
You can enter several settings simultaneously, dividing them by commas.
If the password is set (PASS:XXXX), then before entering any instruction,
you should include its value with no spaces (XXXXSETTINGS1).
General Settings Commands
Request a text message (SMS) with general settings
Request a text message (SMS) with Internet settings
Restore to factory default settings
1) To change the default operation time of the heater use text message
command TIME1:XX, where XX is operation time from 10 to 120 minutes.
2) When using the auxiliary output OUT as a controlling signal for the
car's interior ventilation, set the delay time for switching on of OUT after
the heater's start using setting TIME2:XX, where XX is a value from 1 to 20
minutes.
3) When using the auxiliary output OUT as a controlling signal for the
coolant pump, set the delay time for switching off of OUT after the
heater's stop using setting TIME3:XX, where XX is a value from 1 to 9
minutes.
4) To change the mode of auxiliary output OUT into the pulse mode use
setting PULSEOUT:XXX, where ХХХ is the value for the impulse duration
from 1 to 999 seconds.
To change back to the normal mode set the value to 0 («PULSEOUT:0»).
5) To switch auxiliary output OUT to the manual mode use command
SEPAROUT1. In this mode the control of the auxiliary output is carried out
using text message commands ACTIVATE and DEACTIVATE.
6) ) In the SEPAROUT1 mode after setting KEEPOUT1 is activated, the
module saves and then restores the state of OUT when the power supply is
switched off and subsequently switched on.
Default operating time of heater, 10–120 min
Delay before switching on of OUT, 1–20 min
Delay before switching off of OUT, 1–9 min
Command
USSD:*XXX#
Type of button: latching / non-latching
Pulse mode for OUT, 0-OFF (0-999 sec)
GSMINFO
Manual control of OUT (on/off)
Restoring of the state for OUT after power supply
1) By default, the module uses the option of forwarding all incoming
SMS that are not commands to the last phone number registered in the
module or entered into cells NUM1/2/3.
To deactivate this option use commands SMSF0.
2) To switch on the automated sending of status text messages when
the heater's status has been changed, send SMS command SMSW1.
3) In the waiting mode, when the parking heater is switched off, ALTOX
module controls car system voltage. When the voltage drops below the
Command
predefined value XX (SMSV:XX setting), the system will send an alarm SMS
SETTINGS1
text message to the first authorized phone number entered into settings
SETTINGS2
(NUM1/2/3). The next alarm SMS text message about the voltage drop will
SETDEFAULT
be sent in 3 hours.
4) CALL0 setting switches the module into the mode of dropping
incoming calls which allows saving money.
5) NUM1/2/3 commands set up authorized phone numbers. Phone
numbers should be entered in the international format.
6) BTIMER1:N allows receiving an automated SMS with account balance
information every N days. To switch off this option send a SMS command
with value 0 («BTIMER1:0»).
Forwarding of incoming SMS (to switch off use SMSF0)
SMS status when the heater's status changes
SMS about car system voltage drop
CALL1 - response incoming call, CALL0 - dropping call
Setting the password before entering SMS-commands
Save the phone number into cell NUM1
Save the phone number into cell NUM2
Save the phone number into cell NUM3
Save USSD number for account balance requests
Timer for sending SMS with balance, 0-99 days (0-OFF) BTIMER1:10
Timer for sending balance into application, 1-9 hours
Transliteration of cyrillic characters
Technical Settings
User Settings
Command
TIME1:30
TIME2:0
TIME3:0
FIXKEY1 /0
PULSEOUT:0
SEPAROUT1 /0
KEEPOUT1 /0
Command
SMSF1 /0
SMSW1 /0
SMSV1 /0
CALL1 /0
PASS:XXXX
NUM1:+YYYYYYY
NUM2:+YYYYYYY
NUM3:+YYYYYYY
BAL:*XXX#
BTIMER2:5
TRANSLIT1 /0