ClearWater DELUXE SYSTEM Manuel du propriétaire

Parcourez en ligne ou téléchargez le pdf Manuel du propriétaire pour {nom_de_la_catégorie} ClearWater DELUXE SYSTEM. ClearWater DELUXE SYSTEM 2 pages. High rate sand filter

Imprimer la page

TROUBLESHOOTING

MOTOR DOES NOT START:

Make sure motor is plugged in.

Circuit breaker in OFF position.

Thermal Overload in tripped position.

WIRING INSTALLATION INCORRECT: Incorrect line voltage.

Defective wiring.

THERMAL OVERLOAD TRIPS:

Low Voltage.

Wiring installation incorrect.

Dual voltage pumps mis-wired.

Inadequate ventilation.

NO WATER FLOW:

Obstruction of suction or return line.

Clogged impeller.

Suction system air leaks.

Slice Valve Closed.

Clogged Hose Fitting.

Clogged Basket.

Dirty Sand.

CHLORINATOR & BROMINATOR USE WARNINGS

READ AND FOLLOW ALL INSTRUCTIONS! SAVE THESE INSTRUCTIONS!

WARNING! To reduce the risk of injury and product damage:

Feeders are designed to use only Chlorine (Trichloro-s-triazinetrione) or Bromine

(Bromochloro -5, 5 Dimethylhydantoin) tablets, slow dissolving type. UNDER NO

CIRCUMSTANCES MIX Trichlor OR Bromine with Calcium Hypochlorite, with other forms of

concentrated chlorine, or with other chemicals FIRE AND/OR EXPLOSION MAY RESULT.

NEVER use oils or grease to lubricate 0-ring. Oil in contact with Trichlor OR Bromine may result

in FIRE. Caution should be used when removing feeder cap. Do not inhale fumes.

If shock treatments or Algaecides containing chemicals other than sanitizer tablets in feeder

must be used, then turn off feeder OR remove tablets until the shock or algae treatment is

complete and all granules have dissolved. Failure to do so may result

LIMITED WARRANTY

Waterway Plastics manufactures its products and equipment in accordance with very high

standards of workmanship. We use the best materials available and maintain the highest quality

procedures practical in the industry. In accordance, Waterway warrants its products as follows:

All plastics parts such as jets, valves, skimmers, manifolds, suctions, lights, and other plastic

components manufactured by Waterway will be replaced or repaired if the defects are

determined by Waterway to be the responsibility of Waterway Plastics for a period of three years

from the date of installation. The warranty does not cover filter cartridges, D.E. grids, o-rings,

pressure gauges, pump seals, light bulbs or any parts not manufactured by Waterway. Warranty

applies to OEMs and Distributors of Waterway Products.

The Supreme and Hi-Flo Pumps will receive limited warranty from any defect in material or

workmanship of one year from the date of manufacture. This includes the motor but not the

motor seal.

All thermoplastic molded filter bodies and rotational molded sand filter bodies have a warranty

of ten years, warranted on a pro-rata life basis. If a defect becomes apparent during the first

year, the body will be exchanged for a new body if the defects are determined by Waterway to

be the responsibility of Waterway Plastics. If a defect becomes apparent after the first year from

the date of manufacture which, in the opinion of Waterway, will require replacement, the body

2200 East Sturgis Road, Oxnard, CA 93030 • Ph. (805) 981-0262 • Fax (805) 981-9403

www.waterwayplastics.com • [email protected]

EXCESSIVE PUMP NOISE:

Worn Bearings.

Suction Line Clogged.

Pump incorrectly mounted.

Hose Fitting partially closed.

Slice Valve partially closed.

Clogged Trap Basket.

INADEQUATE FILTERING:

Sand level too low.

Inadequately cleaned system.

Excessive dirt load.

Chemical imbalance.

Inadequate system pressure.

SAND FILL CHART:

Model FS016 - 50 lbs

Model FS022 - 150 lbs

Model FS019 - 100 lbs

Model FS026 - 200 lbs

in granules mixing in feeder causing FIRE AND/OR EXPLOSION. The shock or algae treatment

dissolved in water is safe with tablets.

ALWAYS WEAR PROTECTION for eyes, skin and clothing when working with chemicals. Do

not smoke and avoid sparks and open flames. Turn off pump and control valve before opening

chlorinator. Use of bulk chemicals may result in damage to pool.

Chemicals will dissolve very quickly and may cause bleaching to liner due to over-chlorinating,

possibly causing unsafe pool conditions.

Settings in excess of the recommended control setting levels for the chlorinator can result in

excess chlorine being discharged in your pool. This can result in bleaching or discoloration of

areas around the pool inlet or in some cases bleaching of the entire pool liner or paint (CHECK

CHEMICAL RESIDUALS REGULARLY).

will be exchanged for a new tank on an adjusted service pro-rata life basis.

Charges to the owner, on the pro-rata life basis, will be determined by the actual number of

months installed beginning with the date of installation.

Products that fail or become defective during the warranty period, except as a result of improper

installation, bad water chemistry, accidents or negligence on behalf of the owner, freezing,

earthquakes, fire floods, or other acts of nature, shall be repaired or replaces at Waterway's

option without charge to the owner. This process will be completed within 90 days of receipt

of the defective product barring delays caused by the acquisition of component parts not

manufactured at our facility.

To obtain warranty replacements or repair, defective products should be returned

(transportation paid) to the place of purchase, or to Waterway. It should include a description of

the defect and the circumstances surrounding the incident or problem.

Waterway shall not be responsible for cartage, removal and/or reinstallation labor, or any

other such costs incurred in obtaining warranty replacements. Warranty applies to OEMs and

Distributors of Waterway Products.

This warranty gives you specific legal rights. You may also have other rights which very from

state to state.

810-0081.1208

HIGH RATE SAND FILTER

DELUXE SYSTEM

OWNER'S MANUAL