Fitness Quest Total Gym Shaper Manuel du propriétaire - Page 6

Parcourez en ligne ou téléchargez le pdf Manuel du propriétaire pour {nom_de_la_catégorie} Fitness Quest Total Gym Shaper. Fitness Quest Total Gym Shaper 8 pages. Exercise system

Imprimer la page
HOW TO TT CH THE LEG PULLEY CCESSORY KIT (OPTION L)
Leg Pulley Accessory Kit (Optional)
Connect the Leg Pulley Bracket to the top of the Vertical Column by
1.
aligning Bracket with the hole at the top of the column. (Be sure
Bracket is right side up.) Insert Long Hitch Pin through the hole to
secure Bracket onto the Vertical Column (See Fig. 1).
2.
Detach the Cable Assembly from the loop on the underside of the
Glideboard and attach one of the Clips from the Leg Pulley Assembly.
3.
Place D-Ring on Pulley first. Then connect the D-Ring to the
Bracket as shown. (See Fig. 2)
NOTE: If Rope appears to be twisted, take D-Ring off and turn
Pulley around.
4.
Attach the Foot Harness to one of your feet by placing your foot in
the Harness so the sewn-in-ring is on the bottom of your foot.
Pull tightly on the belt so the Harness is secure. (See Fig. 3)
5.
(a) Position yourself on the Glideboard correctly for the specific
exercise you want to perform.
(b) While lying down on the Glideboard, connect the Clip on
the end of the Rope to an O-Ring on the Harness attached
to your foot. (See Fig 4) Depending on the exercise you are
performing, connect the Clip to the proper O-Ring. Be sure to
always stabilize the Glideboard when clipping the Harness on or
off. Also, use caution when getting on or off the Glideboard. You
are now ready to exercise using the Leg Pulley Accessory.
See your Exercise Guide for specific exercises that utilize the
Leg Pulley Accessory.
NOTE: Remove Leg Pulley Bracket when you are not
exercising with it.
(c) To disconnect the Harness, unclip the Rope from
the O-Ring on the Harness. Be sure to stabilize
Glideboard when disconnecting Foot Harness.
— 8 —
Fig. 1
Long Hitch Pin
Bracket
Fig. 2
TOP VIEW
Fig. 3
O-Ring (loose)
TOP VIEW
Harness
Buckle
Left Foot
O-Ring (sewn in)
O-Ring (loose)
Fig. 4
Left Foot
Right Foot
Right Foot
TOP VIEW
Clip
Left Foot
Right Foot
(b) Take hold of the Vertical Column and pull it up until it is upright. Release
the Spring Loaded Pin. You should hear it lock back into place.
IMPORTANT: Be sure the Spring Loaded Pin is locked into
place before using your unit. You will know the pin is
locked into place when you can see the end protrude
through the inside of the Rail Bracket.
6.
(a) Position one foot on Back Crossbar to keep the product from lifting
off the floor. With one hand on either the Right or Left Rail and the other
hand holding the "C" Pin with Lanyard, slide the Rails up along the Vertical
Column. Line up the hole to the first (lowest) position
on the Vertical Column.
Bracket
(b) Insert "C" Pin with Lanyard
from the back as shown.
7.
(a) Push the "C" Pin with Lanyard down into its locked position (it should lay
flat against the Vertical Column).
D-Ring
Never sit on or exercise on the unit without the "C" Pin with Lanyard
Pulley
securely locked into place.
(b) Insert "C" Pin in the side hole located at the bottom of the Vertical Column.
(This is the pin you removed in step 5a).

STOPPER ASSEMBLY

Foot Harness
8.
If the Stopper at the bottom of the Vertical Column has not already been
installed, please do so now. Unscrew Nut on the end of the Stopper and
remove. Insert the Stopper into the hole located in the center of the Back
Crossbar. (See Fig. 1).
Screw the Nut back onto the Stopper and tighten with Allen Wrenches
provided. (See Fig. 2).
IMPORTANT: Proper installation of the Stopper is necessary
for the Tube Rollers to function easily when the unit is folded and
rolled into place for storage.
5b.
Release
Spring
Loaded
Pin
6a.
6b.
"C" Pin with
Lanyard
7a.
7b.
"C" Pin
Vertical
Column
8.
— 5 —
Pull Vertical
Column Up
Fig. 1
Fig. 2