djm direct VMA915-O Manuel d'instructions - Page 5
Parcourez en ligne ou téléchargez le pdf Manuel d'instructions pour {nom_de_la_catégorie} djm direct VMA915-O. djm direct VMA915-O 6 pages. Valet machine wet & dry 30ltr stainless bin
Imprimer la page9.20. Select the vacuum mode, indicated by the following symbol,
strokes. Apply more detergent in any particularly dirty area. The dirty solution is visible as it is sucked up through the carpet lance
(17). Stop vacuuming when there is no more dirty fluid visible. Do not walk over any newly cleaned area until it is completely dry.
9.21. The hand held lance (11) is ideal for cleaning sofas, chairs, stairs and car interiors.
WARNING! DO NOT replace furniture until the carpet is completely dry!
R
WARNING! DO NOT run the pump when there is no detergent in the detergent tank (6).
R
WARNING! The motor noise changes to a higher pitch when the main drum (19) is full or blocked. Stop the machine immediately
R
and empty the main drum (19).
WARNING! Always use a low foam detergent (Sealey part no: VMR921S) or use a de-foaming agent (Sealey part no: VMR922S).
R
STORAGE:
9.22. Prior to storage, following steps should be taken:
9.23. Remove the carpet lance (17) and use the end of the stainless steel extension tube (12) to suck up any remaining liquid. Run the
machine until the tubes and suction hose (13) are clean and dry.
9.24. Switch off the machine and unplug from the power supply. Empty the main drum (19) using the drainage outlet (7) and empty the
detergent tank (6).
9.25. Remove the foam filter (9) to dry. Refit for further wet suction. For dry vacuuming, fit a dry cartridge filter (8).
WARNING! Always use low foaming shampoo VMR921S 1 litre or VMR925S 5 litre .
R
10. MAINTENANCE
10.1. GENERAL MAINTENANCE.
10.2. Ensure the machine is unplugged from the power supply.
10.3. Disconnect the suction hose (13) from the main drum (19).
10.4. Undo the clasps and remove top section (18) from the main drum (19).
10.5. Clear out any dirt or debris from the main drum (19) and hose (13).
10.6. Clean the foam filter (9) by washing it in a mild soapy solution.
10.7. Check that the stainless telescopic tube (12) operates smoothly, and check the power cable to make sure it has not received any
damage.
CARTRIDGE FILTER MAINTENANCE. (SEE ALSO SECTION 7)
10.8. Handle the cartridge filter carefully (8) when cleaning or installing.
10.9. Carefully remove the cartridge filter (8) and inspect it for damage. A filter that has small holes or tears in it will not perform
efficiently and should be replaced.
10.10. Trouble
10.11. To clean a dry filter, tap it inside a waste bin.
10.12. Do not use a wet cartridge filter for dry vacuuming as the filter will clog quickly. To clean a wet cartridge filter it should
be rinsed from the inside and allowed to air dry for 24 hours.
10.13. To fit a new/cleaned filter, slide it over the filter basket, push it fully home and lock in place with the lid.
REPLACING REMOTE CONTROL BATTERY. (SEE FIG.2)
10.14. Carefully push the hook at the front of the battery cover and lift until the battery cover is released.
10.15. Remove the old battery.
10.16. Insert the new battery with the terminals in the direction shown inside the battery compartment.
10.17. Replace the battery cover.
IMPORTANT: Only replace the battery with a 23AE 12V Alkaline battery.
V
to suck up the dirty solution and repeat the previous pattern of
Fig 2
Original Language Version
VMA915-O
Issue:1 - 19/05/15