AimSafety PM100 Manuel de démarrage rapide
Parcourez en ligne ou téléchargez le pdf Manuel de démarrage rapide pour {nom_de_la_catégorie} AimSafety PM100. AimSafety PM100 2 pages. Personal single gas monitor
Imprimer la page
AimSafety PM
100
Personal Single Gas Monitor
Quick Start Guide
Please refer to the PM
User's Manual for additional
100
product information and features.
www.aimsafety.com
AimSafety
Contact Information
Technical Support
Monday - Friday 8:00 AM to 5:00 PM Central (US) time.
Email: [email protected]
Phone (toll-free): 1-844-325-3050
World Headquarters
3601 North St. Paul Avenue
Sioux Falls, SD 57104 USA
Phone: 1-877-367-7891
Fax: 1-605-951-9616
WARNINGS
Any unauthorized attempt to repair or modify the product, or any other cause of
damage beyond the range of the intended use, including damage by fire, lightning,
or other hazard, voids liability of the manufacturer.
Activate this product only if sensor, visual, detection, and audible cover are clear
from contaminants such as dirt and debris that could block the area where gas is
to be detected.
Do not clean and rub the LCD screen of the products with a dry cloth or hands in
hazardous environment to prevent static electricity.
Perform cleaning and maintenance of the products in fresh air that is free of
hazardous gases.
Test the response of the sensor regularly with a gas concentration exceeding the
alarm set point.
Test LED, audio, and vibration manually.
Gas concentration measurements by the sensor can vary based on the
environment (temperature, pressure and humidity). Therefore, calibration of
PM
should be performed in the same (or similar) environment of the device's
actual use.
100
If the temperature changes sharply during use of the device (e.g., indoors vs
outdoors), the value of the measured gas concentration can suddenly change.
Please use the PM
Severe vibration or shock to the device may cause a sudden reading change.
Please use PM
shock to PM
All alarm values is set based on the alarm standard that is required by
international standards. Therefore, alarm values should be changed only under
the responsibility and approval of the administration of the work site where the
instrument is used.
Use IR communications in the safety zone which is free of hazardous gases.
Do not attempt to replace the battery and sensor as PM
disposable. Changing the battery and sensor may impair intrinsic safety and the
attempt will void warranty.
CAUTIONS
Before operating this device, please read the manual carefully.
This device is not a measurement device, but a gas detector.
If calibration and self-test fails continuously, please do not use the device.
For the O
environment.
Before use, please check the activation date, and if the activation date has past,
please do not use the device.
Clean detectors with a soft cloth and do not use chemical substances for
cleaning.
To maintain a 24-month lifetime, avoid the below activities except in
necessary cases to check events(Max/Min), lifetime/concentration, and alarm
set points. Otherwise, the frequent use of the button will deplete the battery
lifetime less than 24 months.
1. Push the button frequently without valid reasons.
2. Frequent alarm operation or alarms are remained for a long time.
*Normal Alarm Use: 1 time and 2 minutes per day.
3. Connect with the PM Link frequently except the bump testing.
View a serial number on the label at the back side of the device. (ex,
20170101)
1. The serial number indicates below.
ex) SG 01 01 001
P/N: 34-2900-0211-0 Rev.:A
after the gas concentration value has stabilized.
100
after the value of gas concentration has stabilized. Excessive
can cause the device and/or sensor to malfunction.
100
100
is designed to be
100
detector, perform calibration every 30 days in the fresh air
2
2017(Year) 01(Months) 01(Day) 001(Manufacture Order)
Product Overview
Monitor
Display
Display symbols