Altronix HubSat Series Manuel d'installation - Page 3
Parcourez en ligne ou téléchargez le pdf Manuel d'installation pour {nom_de_la_catégorie} Altronix HubSat Series. Altronix HubSat Series 12 pages. Passive utp transceiver hub with integral camera power
Imprimer la page
Altronix HubSat8DV Passive UTP Transceiver Hub with Integral Camera Power transmits UTP video, RS422/
RS485 data and power over a single CAT-5 or higher structured cable . Unit provides 8 camera channels in a wall
mount enclosure . Video transmission range is up to 750 ft . max . per channel . Units are compatible with AC and/
or DC fixed or PTZ cameras when utilizing Altronix HubWayAv, HubWayAv2, HubWayDv or HubWayDvi
Video Balun/Combiners . In addition, the unit features individually selectable 24VAC or 28VAC PTC protected
outputs with surge suppression . Optionally, the HubSat8DV can be used as an accessory module to transmit
video from up to 8 cameras over a single CAT-5 or higher structured cable back to the HubWay, HubWayLD or
HubWayLDH Passive and Active UTP Transceiver Hubs . In addition, the HubSat8DV provides power to these
cameras locally to eliminate the possibility of voltage drop associated with long cable runs .
Agency Listings:
• CE European Conformity
Input:
• 220VAC 50/60Hz, 1A .
Video:
• Eight (8) channels of quality video over twisted pair
up to a distance of 750 ft . per channel .
• Eight (8) 75 Ohm video outputs .
Data:
• RS422/RS485 data input .
Power:
• Individually selectable 24VAC or 28VAC power
outputs with OFF position .
• Unit provides up to 1A max . per channel not to
exceed a total of 8A maximum current .
HubSat82DV
• HubSat8DV with eight (8) HubWayAv
Video Balun/Combiners for 24VAC Cameras .
WARNING: To reduce the risk of fire or electric shock do not expose the unit to rain or moisture.
This installation should be made by qualified service personnel and should conform to all local codes.
HubSat8DV Passive UTP Transceiver Hub with Integral Camera Power.
1 . Mount unit in desired location . Mark and predrill holes in the wall to line up with the top two keyholes in
the enclosure . Install two upper fasteners and screws in the wall with the screw heads protruding . Place the
enclosure's upper keyholes over the two upper screws; level and secure . Mark the position of the lower
two holes . Remove the enclosure . Drill the lower holes and install two fasteners . Place the enclosure's
upper keyholes over the two upper screws . Install the two lower screws and make sure to tighten all
screws (Enclosure Dimensions, pg. 12) . Secure green wire lead to earth ground .
2 . Set illuminated master power disconnect circuit breaker to the (OFF) position (Fig. 3a, pg. 8) .
3 . Connect unswitched AC circuit (220VAC, 60Hz) as follows: Green branch wire (ground) connects to
the terminal marked
marked [N] of the Inlet Appliance Connector (Fig. 3, pg. 8) . The power LEDs (Green) for Channels 1-8 of
the HubSat8DV will illuminate when AC power is present (Fig. 1e, pg. 6)
4 . Select 24VAC or 28VAC power output for Channels 1-4 with the corresponding voltage adjustment
switches (Fig. 1d, pg. 6) .
5 . Connect the BNC video outputs for HubSat8DV Channels 1-8 to the corresponding video inputs
on the head end equipment (DVR) (Fig. 1a, pg. 6) .
6 . Connect the RS422/RS485 output of the head end equipment (DVR) to the data terminals marked
[+ DATA –] of the HubSat8DV unit (polarity must be observed) (Fig. 1f, pg. 6) .
Note: The Data input terminals of the HubSat8DV must be wired in parallel for proper operation .
When using fixed cameras disregard this step .
HubSat8DV
Overview:
Specifica tions:
Additional Models:
Installation Instructions:
, Line connects to the terminal marked [L], and Neutral connects to the terminal
Input
220VAC 60Hz
Power (cont.):
• PTC protected outputs are rated @ 1A per channel .
• Surge suppression .
Visual Indicators:
• Eight (8) power LED indicators .
Enclosure Dimensions (H x W x D approx.):
13 .5" x 13" x 3 .25"
(342 .9mm x 330 .2mm x 82 .6mm)
Optional Accessories:
• Video Balun/Combiners:
- HubWayAv:
- HubWayAv2:
- HubWayDv:
- HubWayDvi:
HubSat83DV
• HubSat8DV with eight (8) HubWayDv
Video Balun/Combiners for 12VDC Cameras .
for use with 24VAC cameras .
for use with 24VAC cameras .
for use with 12VDC cameras .
for use with non-isolated
12VDC cameras .
- 3 -