Altronix AL1002ULADA Manuel d'application - Page 6
Parcourez en ligne ou téléchargez le pdf Manuel d'application pour {nom_de_la_catégorie} Altronix AL1002ULADA. Altronix AL1002ULADA 8 pages. Nac power extenders
Également pour Altronix AL1002ULADA : Manuel d'installation (13 pages), Manuel d'installation (17 pages), Manuel d'application (8 pages), Manuel d'application (8 pages)
Imprimer la page
Output Programming Selection Table:
Outputs must be programmed independently (OUT1 - OUT4)
Function
Input to Output
Follower Mode
Temporal Code 3
Mode
Steady Mode
March Time Mode
(60 beats per minute)
For the above modes Dip Switch 4 determines which Input controls
the corresponding output:
Switch 4 in the ON position causes output(s) to be controlled by input 1.
Switch 4 in the OFF position causes output(s) to be controlled by input 2.
Sync Mode Selection Table:
Function
Amseco
Sync Mode*
Faraday
Sync Mode*
Gentex
Sync Mode*
Gentex is a registered
trademark of Gentex Corporation.
System Sensor
Sync Mode*
System Sensor is a registered
trademark of Honeywell.
Note: The AL602ULADA, AL802ULADA, and AL1002ULADA will only synchronize horns, horn strobes
and strobes that contain synchronization capability. Contact signal manufacturer for more detailed info.
The same synchronization mode must be selected for all outputs.
* It is required to control visual notification appliances (strobes) via input 1 (IN1) and audible notification
appliances (horns) via input 2 (IN2). This allows audible notification appliances (horns) to be silenced while
visual notification appliances (strobes) continue to operate.
Switch Positions Descriptions
ON
OFF
1
2, 3
Output follows signal it receives from the corresponding input (i.e. FACP
Sync module - maintains synchronization of notification appliance circuit.
3
1, 2
Enables Temporal Code 3 signal generation output.
This mode is activated by a steady or a pulsing input.
1, 2, 3 A steady output signal will be generated. This mode is activated by
a steady or pulsing input.
2, 3
1
Enables a March Time output which will sound 60 beats
per minute. This mode is activated by a steady or pulsing input.
Switch Positions Descriptions
ON
OFF
1, 3, 4
2
This mode is designed to work with the Amseco series of horns, strobes,
and horn/strobes to provide a means of synchronizing the Temporal-coded
horns, synchronizing the flash timing of the strobe, and silencing the horns
of the horn/strobe combination over a two-wire circuit while leaving
strobes active.
2, 4
1, 3
This mode is designed to work with the Faraday series of horns, strobes,
and horn/strobes to provide a means of synchronizing the Temporal-coded
horns, synchronizing the flash timing of the strobe, and silencing the horns
of the horn/strobe combination over a two-wire circuit while leaving
strobes active.
1, 2,
This mode is designed to work with the Gentex
3, 4
and ST/HS series of horns, strobes, and horn/strobes to provide a
means of synchronizing the Temporal-coded horns, synchronizing the
flash timing of the strobe, and silencing the horns of the horn/strobe
combination over a two (2)-wire circuit while leaving strobes active.
1, 2, 4
3
This mode is designed to work with the SpectrAlert
strobes, and horn/strobes to provide a means of synchronizing the
Temporal-coded horns, synchronizing the one-second flash timing
of the strobe, and silencing the horns of the horn/strobe combination
over a two-wire circuit while leaving strobes active.
- 6 -
(AL800LGK Board)
Output Dip Switches
INPUT SELECT
TEMPORAL
STROBE SYNC
IN>OUT SYNC
®
Commander GOS
TM
series of horns,