CustomWorks INTIMIDATOR GSX2 Manuel - Page 12

Parcourez en ligne ou téléchargez le pdf Manuel pour {nom_de_la_catégorie} CustomWorks INTIMIDATOR GSX2. CustomWorks INTIMIDATOR GSX2 17 pages. Racing kit

Imprimer la page

Tire Bag

Tire & Wheel Installation

-Parts for

Tire Bag

6204

Qty 2

Street-Trac FRONT

NOTE:

In this step you will be using a fast drying super glue

NOTE: In this step you will be using a fast drying super glue

NOTE:

In this step you will be using a fast drying super glue

type adhesive to secure the tires and wheels to each other. Be

very careful with this process as the glue can tend to run very

easilly through the tire and may glue your finger to the tire or

wheel before you know it. You must follow the directions and

precautions provided by the glue manufacturer to insure a

secure bond.

STEP #1: Using a reamer or a small drill bit make a hole in the

STEP #1:

center of each of the 4 wheels as shown in Figure 1.

STEP #2: Place the foam inserts into the tires with the wider

STEP #2:

inserts going in the rear tires, the narrower in the fronts. Make

sure the insert is laid into the tire evenly. As shown in Figure 2

it should not be bunched up too much in any area.

STEP #3:

STEP #3: Place the wheel inside of the tire and work both

STEP #3:

beads of the tire into the channels on the outside edge of the

wheel. Peel back a portion of the tire from the wheel and

apply an even bead of tire glue between the wheel and the

tire as shown in Figure 3.

Figure 3.

Figure 3. Repeat this step several times

Figure 3.

working your way around the tire until it is secure. You may

repeat this process now for the remaining 3 tires BUT BE

SURE TO PLACE THE FRESHLY GLUED SIDE UP

SURE TO PLACE THE FRESHLY GLUED SIDE UP until it has

SURE TO PLACE THE FRESHLY GLUED SIDE UP

dried completely. Once dry it is a good idea to go back and re-

seal the edges by applying another small bead of glue and

letting it run around the edge of the tire at the gap between

tire and wheel.

STEP #4:

STEP #4: Once the tires have completely dried you may now

STEP #4:

mount them to the car. Place one #1226 Bearing into each

side of the front wheels as shown in Figure 4.

STEP #5:

Figure 5

STEP #5:

STEP #5: Refer to Figure 5

Figure 5

Figure 5 and place one 7047 shim over the front axle followed bye the front wheel and then the

7220 Axle Spacer. Now secure with one 5207 Locknut, be very careful to not overtighten the nut. you want to tighten

it just enough to eliminate any slop from side to side but no more. Repeat for other side of car.

STEP #6:

STEP #6: Now slide one of the rear wheels onto the rear axle as shown in Figure 6.

STEP #6:

axle so that it slides into the drive slot molded in the back of the wheel. Now secure with a 5207 locknut. Be sure not

to over tighten as you can bend the roll pin.

NOTE: Wheel should spin freely when wheel nut is tight to the wheel. If it is tight remove some of the 7047 Shims on

the axle. If the axle still has alot of side to side play, add more 7047 shims until wheels spins freely without the side to

side play.

6214

Qty 2

6220

Qty 2

Street-Trac REAR

Soft Insert FRONT

Figure 1.

Figure 4.

6221

Qty 2

6252

Qty 2

Soft Insert REAR

Front Wheel

Figure 1

Figure 2

Figure

BUT BE

7047

Figure 5

5207

Qty 4

8-32 Lock Nut

1226

6253

Qty 2

Ball Bearing

Rear Wheel

Figure 2

Figure 4

7220

Figure 6

Figure 6.

Figure 6. Be sure to index the roll pin in the

Figure 6.

1:1

7047

Qty 6

Spacer

1:1

Qty 4

7220

Qty 2

Axle Spacer