AKO AKO-D14420 Instructions d'installation
Parcourez en ligne ou téléchargez le pdf Instructions d'installation pour {nom_de_la_catégorie} AKO AKO-D14420. AKO AKO-D14420 2 pages.
D144H232 Ed.08
GB
Installation instructions
AKO-D14412
AKO-D14420
AKO-D14123-2-RC
AKO-D14412-RC
3-
Wiring
The probe and its cable should NEVER be installed in the same conduit as power, control or supply cables.
AKO-D14123-2-RC
Modbus*
12
13
14
15
2 CV
1
2
3
4
5
6
7
8
9
10
11
90-240 V~
COOL (P0=0)
50/60 Hz
RES (P0=1)
R. CRANKCASE
AUX Relay
S1: Probe 1, temperature in the chamber or cabinet
Function as per
S2/DI2: Probe 2, defrost or digital input 2 (as per P4)
AUX.
parameter P6
S3/DI1: Probe 3, temperature of product / 2nd defrost, or digital input 1 (as per P4)
DI1: Digital Input 1
AKO-D14412 / D14412-RC
Modbus*
12
13
14
15
1
2
3
4
5
6
7
8
9
10
11
_ ~
12 V
COOL
FAN
DEF
AUX
*according to model
4-
Operation
Display
Program Mode
FAN relay ON
ECO relay
ON
COOL relay ON (P0=0)
ESC
SET
Fast Freezing
AUX relay ON
mode
RES relay ON (P0=1)
Standby
mode
DEF relay ON
%
ESC key /
Press for 5 seconds to start/stop Fast Freezing mode (rapid
cooling).
In the programming menu, exit without saving parameter,
return to previous level or exit programming.
SET key
Press for 5 seconds to modify the set point (SP) (Set Point).
Press for 10 seconds to go to the programming menu.
In the programming menu, go to the level displayed or accept
the new value while setting a parameter.
1- Warnings
-Using the equipment without following the manufacturer's
instructions may affect the device's safety requirements. To ensure
that the device operates correctly, only probes supplied by AKO
should be used.
-The unit must be installed in a location protected from vibrations,
water and corrosive gases, where the ambient temperature does
not exceed that shown in the technical data.
-To ensure a correct reading, the probe must be situated in a
location without any external heat influences except for the
temperature which is being measured or controlled.
-The power supply circuit must be provided with a main switch rated
at at least 2 A, 230 V, located close to the equipment. The cables will
enter through the back and should be type H05VV-F or H05V-K.
-The gauge will depend on local regulations, but should in no case
be less than 1 mm .
-Connecting wires for the relay contacts should be sized 2.5 mm .
-Between -40 ºC and +20 ºC, if the probe NTC is prolonged till
1.000 m with a mínimum of cable 0,5 mm², the maximum devia-
tion will be of 0,25 ºC (extension cable for probe ref. AKO-15586)
AKO-D14423
NOTE: Equipment not compatible with AKO-14917 (external commu-
AKO-D14323-C
nication module) and AKO-14918 (programming key)
AKO-D14423-RC
I max.:
16 A
L N
I max.:
16 A
L N
AKO-D14423
AKO-D14423-RC
AKO-D14420
AUX.
N
Up key
Pressing for 5 seconds starts/stops defrosting.
The programming menu, allows you to scroll through the various
levels or, during the setting of a parameter, to change the value.
Q
Down key
Pressing for 5 seconds activates Standby mode, pressing for 2
seconds returns the equipment to normal mode. In Standby mode,
the equipment performs no actions and only the indicator is
displayed on the screen m.
The programming menu, allows you to scroll through the various
Keyboard
levels or, during the setting of a parameter, to change the value.
4.1- Access to set point and programming
SET
Temperature
Indication
Change set point (SP)
Current
Value
2
AKO-D14323-C
Modbus*
12
13
14
15
16 A
6 A
8 A
1
2
3
4
5
6
7
8
9
10
11
90-240 V~
AUX
50/60 Hz
FAN
COOL
R. CRANKCASE
AKO-D14423 / D14423-RC / D14420
Modbus*
12
13
14
15
1
2
3
4
5
6
7
8
9
10
11
COOL
FAN
230 V
~ 50/60 Hz
DEF
90-240 V~ 50/60 Hz
120 V~ 50/60 Hz
AUX
H
/
m
/
5 sec.
10 sec.
t
Release SET
Release SET
to access the
to access
set point
programming
Change
Accept value
value
and exit
SET
New
Temperature
Value
Indication
2- Installation
2
Programming Menu (parameters)
Change
menu
I max.:
OK
16 A
L N
SET
Level 1
Level 2
Menus
Parameters
ESC
ESC
Exit Programming
Return to
Level 1
AUX.
Back up one level without saving changes
ESC
5- Start-up
On power-up, the equipment will start up in Wizard mode
(P3 / 1 flashing), press N or Q to select the most
appropriate application and press SET.
1: Multipurpose 2: Frozen
I max.:
4: Fresh fish
5: Soft Drinks
16 A
7: AC
8: Heat / Incubators
L N
The wizard will configure the parameters of the equipment for
the chosen application (see table "Default settings by
application").
WARNING: The default parameters by type of
application have been defined for the most
common applications. Check that these
parameters are suitable for your installation.
DEFAULT SETTINGS BY APPLICATION (InI)
1
2
3
AUX.
2
-18
10
SP
(35,6ºF)
(-0,4ºF)
(50ºF)
d0
4
4
4
d1
20
20
20
8
0
30
F0
(46ºF)
(32ºF)
(86ºF)
F3
1
0
1
P0
0
0
0
7 1 m m
Change
Change value
param.
OK
OK
SET
SET
Level 3
Values
3: Fruits and vegetables
6: Bottle racks
4
5
6
7
8
0
3
12
21
37
(32ºF)
(37,4ºF)
(53,6ºF)
(69,8ºF)
(98,6ºF)
-
4
24
24
96
20
20
20
0
-
8
8
30
99
-
(46ºF)
(46ºF)
(86ºF)
(211ºF)
1
1
1
1
-
0
0
0
0
1