Do-All Outdoors Firefly Manuel d'utilisation - Page 2

Parcourez en ligne ou téléchargez le pdf Manuel d'utilisation pour {nom_de_la_catégorie} Do-All Outdoors Firefly. Do-All Outdoors Firefly 2 pages.

Imprimer la page
FOR QUESTIONS REGARDING THE FIREFLY PLEASE CALL OUR
CUSTOMER SERVICE DEPARTMENT AT (800-663-3712) OR VISIT
OUR WEBSITE WWW.DOALLOUTDOORS.COM FOR ADDITIONAL
INFORMATION AND VIDEOS. THANK YOU FOR YOUR BUSINESS!
COMPONENTS:
FF550
•
MAIN UNIT
•
2 - FRONT LEGS
•
2 - FRONT LEG BRACKETS
•
4 - ALLEN SCREWS FOR FRONT LEGS
(5/32" ALLEN WRENCH)
•
2 - FRONT SAFETY RING BRACKETS
•
2 - REAR SAFETY RING BRACKETS
•
1 - SAFETY RING
•
1 - REAR BASE
•
1 - HORSESHOE FOR STACKER POLES
•
4 - STACKER POLES
•
4 - BOLTS FOR HORSESHOE
(11MM WRENCH)
•
1 - SPRING
•
1 - SPRING BOLT
•
1 - SPRING BOLT KNOB
ASSEMBLY
1) REMOVE UNIT FROM BOX
2) INSTALL THE TWO FRONT LEG
BRACKETS AND THE TWO FRONT
SAFETY RING BRACKETS.
3) INSERT THE TWO FRONT LEGS INTO
BRACKETS
4) INSTALL REAR BASE
5) INSTALL THE TWO SAFETY RING
BRACKETS AT THE REAR OF UNIT
6) INSTALL SAFETY RING
7) INSTALL THE FOUR STACKER POLES
AND HORSESHOE
8) MOVE ARM INTO THE TWELVE
O'CLOCK POSITION
(POINTING AWAY FROM UNIT)
9) INSTALL SPRING AND SPRING BOLT.
INSERT THE SPRING BOLT INTO
THE SPRING. THEN CONNECT THE
SPRING TO THE EYELET UNDER-
NEATH THE UNIT. RUN THE SPRING
BOLT THROUGH THE HOLE IN THE
REAR OF THE UNIT.
10) INSTALL SPRING BOLT NUT. DO NOT
APPLY TOO MUCH TENSION.
11) UNIT IS NOW READY FOR
OPERATION
12) YOU CAN FIND SUPPORTING
VIDEOS FOR THE FIRE FLY ONLINE
AT WWW.DOALLOUTDOORS.COM
2
OPERATION
•
MAKE SURE UNIT IS POINTED IN A SAFE DIRECTION
•
PUSH FRONT LEGS FIRMLY INTO GROUND. DO NOT APPLY PRESSURE TO THE TOP OF UNIT
•
LOAD CLAYS
•
CONNECT CABLES TO 12V MARINE BATTERY (RED TO POSITIVE AND BLACK TO NEGATIVE)
•
SWITCH MACHINE TO THE ON POSITION
•
THE ARM WILL SLOWLY SWING AROUND AND PICK UP A CLAY AND STOP.
•
FIRE BY DEPRESSING THE FOOT PEDAL. KEEP PRESSURE ON THE FOOT PEDAL UNTIL CLAY
IS LAUNCHED. NEVER KEEP CONSTANT PRESSURE ON THE FOOT PEDAL. ALWAYS TAKE OFF
YOUR FOOT OF THE PEDAL BETWEEN LAUNCHES.
•
WHEN FINISHED SHOOTING, TURN MACHINE OFF AND DISCONNECT FROM BATTERY.
•
WHEN NOT IN USE, TURN UNIT OFF. DISCONNECT UNIT FROM BATTERY. RELEASE TENSION
FROM SPRING BY LOOSENING SPRING BOLT NUT. YOU MAY CHOOSE TO REMOVE SPRING
COMPLETELY.
•
ALWAYS REMOVE THE SPRING AND DISCONNECT UNIT FROM THE BATTERY WHEN MAKING
ADJUSTMENTS.
•
YOU CAN ADJUST THROWING DISTANCES BY LOOSENING OR TIGHTENING THE SPRING. NEVER
OVERTIGHTEN SPRING.
•
ONCE YOU ARE READY TO STOP SHOOTING, THE TRAP MUST BE RELIEVED OF TENSION
WHILE STORING, OTHERWISE THE UNIT IS ALWAYS ARMED AND UNDER PRESSURE. TO AVOID
ACCIDENTAL DISCHARGE, SPRING TENSION MUST BE RELIEVED BY LOOSENING THE KNOB AND
REMOVING THE SPRING. ONCE YOU ARE READY TO SHOOT AGAIN, YOU MUST REPEAT STEP 8
AND MOVE THE ARM INTO THE 12:00 POSITION AND REATTACH SPRING AND SPRING HANDLE IN
ORDER TO KEEP THE TRAP IN TIME.
•
ALWAYS STORE TRAP IN A DRY AREA, KEEP LUBRICATED AND FREE OF DEBRIS
TROUBLESHOOTING
NOT DROPPING CLAYS IN PROPER SEQUENCE:
YOUR TRAP IS MOST LIKELY OUT OF TIME. YOU CAN ADJUST TIMING IN THE FIELD BY ADJUSTING
THE LIMIT SWITCH WITH AN ALLEN WRENCH. IF LIMIT SWITCH ADJUSTMENT ARE NEEDED, YOU
MUST TURN THE MACHINE OFF, DISCONNECT TRAP FROM THE BATTERY AND RELIEVE TEN-
SION, THEN REMOVE THE MAIN SPRING. IF THE ARM IS STOPPING TOO EARLY, MOVE THE LIMIT
SWITCH SLIGHTLY TO THE RIGHT. IF THE ARM IS STOPPING TOO LATE, MOVE THE LIMIT SWITCH
TO THE LEFT. YOU MIGHT HAVE TO MAKE A FEW ADJUSTMENTS BEFORE GETTING IT RIGHT.
YOU CAN CHECK TIMING BY ROTATING THE ARM AND CHECKING ITS POSITION WHEN THE CLAY
IS DROPPED IN RELATION TO WHEN THE LIMIT SWITCH IS ACTIVATED. ONCE TIMING HAS BEEN
CORRECTED, PLEASE REPEAT STEPS 8 THROUGH 10 TO BEGIN SHOOTING.
• PLEASE CHECK THAT ALL WIRING CONNECTIONS ARE SECURE
• MAKE SURE BATTERY IS FULLY CHARGED
• IF YOU ARE UNABLE TO MAKE CORRECTIONS IN THE FIELD, PLEASE CALL 866-SHOT-DOC
IF UNIT IS NOT OPERATING PROPERLY, PLEASE CONTACT 866-SHOT-DOC FOR ASSISTANCE.
DO NOT RETURN TO STORE
DO-ALL OUTDOORS, LLC. PRIDES ITSELF ON ITS CUSTOMER SERVICE. PLEASE CONTACT
US IF YOU HAVE ANY ISSUES WITH OUR PRODUCT.
3