Dodge 078290 Manuel d'instruction

Parcourez en ligne ou téléchargez le pdf Manuel d'instruction pour {nom_de_la_catégorie} Dodge 078290. Dodge 078290 8 pages.

Imprimer la page

These instructions must be read thoroughly before installation or operation. This instruction manual was accurate at the time of

printing. Please see dodgeindustrial.com for updated instruction manuals.

WARNING: To ensure the drive is not unexpectedly started, turn off and

lock-out or tag power source before proceeding. Failure to observe these

precautions could result in bodily injury.

WARNING: Only qualified personnel familiar with hydraulic and electrical

installations, the construction and operation of this equipment, and the

hazards involved should install, adjust, operate, and/or service it. Read

and understand this manual in its entirety before proceeding. Failure to

observe this precaution could result in severe bodily injury or loss of life.

SYSTEM SPECIFICATIONS

System Part

Number

Motors Information

063488

Single Phase—115/230 VAC

063487

Three Phase—230/460 VAC

Three Phase—208-230/460 VAC

078289

(Explosion Proof Motors)

078290

Three Phase—575 VAC (Canada)

NOTE: For Cool Lube 2 Material Details, please refer to cut sheets.

Air to oil heat exchanger: Thermal Transfer BOL-8-2

* Pump Relief valve setting: 150 psi

* Bearing Relief valve setting: 65 psi

Pump flow rate: 2 GPM

Flow meter range: 0.5 – 4.0 GPM

Oil supply line connection:

Oil return line connection: Two 1" NPT connections (female)

* Relief valves are preset at the factory, but are field adjustable. If other

settings are required, consult Dodge Engineering

WARNING: Because of the possible danger to person(s) or property

from accidents which may result from the improper use of products,

it is important that correct procedures be followed. Products must be

used in accordance with the engineering information specified in the

catalog. Proper installation, maintenance and operation procedures

must be observed. The instructions in the instruction manuals must

be followed. Inspections should be made as necessary to assure

safe operation under prevailing conditions. Proper guards and other

suitable safety devices or procedures as may be desirable or as may

be specified in safety codes should be provided, and are neither

provided by Dodge

nor are the responsibility of Dodge. This unit and

its associated equipment must be installed, adjusted and maintained

by qualified personnel who are familiar with the construction and

operation of all equipment in the system and the potential hazards

involved. When risk to persons or property may be involved, a holding

device must be an integral part of the driven equipment beyond the

speed reducer output shaft.

Cool Lube 2 for Sleevoil Pillow Blocks

Part Numbers 063487, 063488, 078289, 078290

Instruction Manual

Approximate

Weights (lbs)

Two 1/2" NPT connections at the

flow meter outlets (female)

WARNING: All products over 25 kg (55 lbs) are noted on the shipping

package. Proper lifting practices are required for these products.

RECEIVING & INSPECTION

Carefully unpack the Cool Lube 2 system. Inspect the system

for any damage during shipping.

Report any damage to the carrier for claims.

Make sure that available voltage supply is within 10% of the

system voltage.

Check all hydraulics to ensure that nothing came loose during

shipping. Tighten as needed.

Changes to this unit may void the warranty.

257

FLOW

METERS

INSTALLATION

Place the unit in the designated area and anchor it down

using the 4 mounting holes in the base plate. The unit should

be positioned below the circulating oil drain holes in the

bearings so that at least a 15° drain line slope is achieved to

allow for adequate oil return (see Figure 1).

Make sure that there is enough space around the unit to allow

for servicing.

Connect oil supply lines (not included) from the two 1/2" NPT

(female) outputs of the flow meters to the circulating oil inlets

on the housings. Connection details for each type of Sleevoil

bearing are provided in sections following (see Figure 2).

NOTE: All plumbing should be cleaned and flushed

before being connected to the bearings.

Figure 1 - Cool Lube 2

BEARING

PRESSURE

GAUGE

Figure 2 - Controls

NEEDLE

VALVES

PUMP

PRESSURE

GAUGE