Clipsulin C3 Manuel - Page 2

Parcourez en ligne ou téléchargez le pdf Manuel pour {nom_de_la_catégorie} Clipsulin C3. Clipsulin C3 2 pages. Universal insulin pens recorder

Imprimer la page

HOW TO OPERATE YOUR CLIPSULIN

1. SETUP

3. USING THE CLIPSULIN

Install a new battery.

Remove the cap of your insulin

pen and install the needle. Click the

Battery type: CR2032.

power button to turn on the CLIPSULIN

Refer to "Battery Replacement"

section.

Clip the CLIPSULIN

onto your insulin

pen in a way that allows you to see the

LCD screen next to the unit window of

your insulin pen.

"00" will be displayed on the CLIPSULIN

Attach the CLIPSULIN

near the dosage

screen.

window.

Select your injection dose on the

Ensure that your CLIPSULIN

is tightly

insulin pen.

ﬁtted onto your insulin pen.

CLIP

Ensure that your hands DO NOT come

into contact with the CLIPSULIN

during dose selection.

Verify that the number of units

displayed on the CLIPSULIN

same as the selected dose on the

insulin pen.

If the numbers are not the same, use

the " + " or " - " button to adjust

manually the units on the CLIPSULIN

2. BEFORE FIRST USE

Go to www.diabnext.com/app and

You can increase the number gradually

install the DIABNEXT

APP on your

by holding down the "+" (plus) button,

mobile device.

or decrease the number gradually by

holding down the "-" (minus) button.

Conﬁrm the two numbers are the same,

then click the blue button (Power) to

validate and send your dosage data.

DIABNEXT

Turn on the Bluetooth function of your

mobile device and open the DIABNEXT

APP.

Enter the menu, select "My Tools" and

click "Add Tools".

The green light and the LCD will blink

Click "Insulin Pens" and select your

to signal that the data has been

insulin pen type.

recorded.

The data will not be recorded if the

Follow the instructions on the APP.

green light and the LCD have not

(Press and hold down the power button

blinked.

of CLIPSULIN

, until you see the double

Your data will be automatically

dash "- -" blinking on the LCD screen,

transmitted to your mobile APP

to pair with the APP.)

after injections. (See the " ★ " part.)

If you do not want your data to be

transferred automatically, please refer

to the "Data Transmission" section.

Perform your injection in your normal

manner.

It will take a few seconds to connect.

"- -" will be displayed on the screen

The device will automatically shut

of CLIPSULIN

down after 10 seconds of inactivity.

DATA TRANSMISSION

BLUETOOTH

You can use the Bluetooth transmitting

function with your mobile phone if you

have iOS / Android with BLE 4.0 or

higher.

Enable the Bluetooth function on

your mobile device.

Open the DIABNEXT

DIABNEXT

Follow the instructions on the APP.

is the

Press and hold down the power button

of CLIPSULIN

, until you see the double

dash "- -" blinking on the LCD screen,

to pair with the APP.

"- -" will be displayed on the screen of

CLIPSULIN

+1 UNIT

Your stored records will be transferred

automatically, and can be viewed on

your mobile device.

-1 UNIT

If you see the "Device error, please

contact customer service" message

2 2 2 2 2 2 2 2 2

pop up, please refer to the

4 4

"Troubleshooting" section.

The dose, date, and time of injection will be automatically stored in your CLIPSULIN

★

The CLIPSULIN

will automatically transmit the stored injection data under these conditions:

1. You have paired your CLIPSULIN

2. The Bluetooth/NFC function is enabled on your smartphone or tablet.

3. Your smartphone or tablet is nearby with the DIABNEXT

your CLIPSULIN

Your CLIPSULIN

can store up to 200 records, but the NFC connection can only transmit the

latest 50 records in the memory. Transfer your records regularly to your smartphone

or tablet to keep track of your injections.

NFC

You can use the NFC transmitting function

with your mobile phone if you have:

- iPhone 7 or newer, and have the iOS 11

system updated or newer.

- Android phone with NFC function.

Enable the NFC (Near Field

Communication) function on your

mobile device.

Note: For iPhone users, you may

skip this step.

APP.

Open the DIABNEXT

APP.

DIABNEXT

Follow the instructions on the APP.

Press and hold down the power button

of CLIPSULIN

, until you see the double

dash "- -" blinking on the LCD screen,

to pair with the APP.

"- -" will be displayed on the screen of

CLIPSULIN

Your stored records will be transferred

automatically, and can be viewed

on your mobile device.

NFC signal

emitting point

The NFC transmitter of the CLIPSULIN

is near the power button. Please

conﬁrm the NFC transmitter location

of your smartphone/tablet, and be

sure to have your smartphone/tablet

close to your CLIPSULIN

for proper

pairing/syncing.

If you see the "Device error, please

contact customer service" message

pop up, please refer to the

"Troubleshooting" section.

Only the latest 50 records can be read

out via NFC connection. Transfer your

records at least once per week to keep

track of your injections.

with the DIABNEXT

APP before.

APP open amd connected to

BATTERY

BATTERY REPLACEMENT

Transfer your stored records before

replacing the battery.

Open the battery compartment.

Replace the old battery with a new

one.

Battery

Push the compartment back into

the CLIPSULIN

to close it.

Click the power button to check the

status of CLIPSULIN

Sync your device with the DIABNEXT

APP before using it again, to ensure

that the timestamps of the records

will be correct.

FCC STATEMENT

This device complies with part 15 of the

FCC Rules. Operation is subject to the

following two conditions:

1. This device may not cause harmful

interference, and

2. This device must accept any interference

received, including interference that

may cause undesired operation.

NOTE:

This equipment has been tested and found

to comply with the limits for a Class B

digital device, pursuant to part 15 of the

FCC Rules.

These limits are designed to provide reasonable

protection against harmful interference in a

residential installation.

This equipment generates, uses and can

radiate radio frequency energy and, if not

installed and used in accordance with the

instructions, may cause harmful interference

to radio communications. However, there

is no guarantee that interference will not

occur in a particular installation.

If this equipment does cause harmful

interference to radio or television reception,

which can be determined by turning the

equipment oﬀ and on, the user is encouraged

to try to correct the interference by one or

more of the following measures:

· Reorient or relocate the receiving antenna.

· Increase the separation between the

equipment and receiver.

· Connect the equipment into an outlet on

a circuit diﬀerent from that to which the

receiver is connected.

· Consult the dealer or an experienced

radio/TV technician for help.

Changes or modiﬁcations not expressly

approved by the party responsible for

compliance could void the user's authority

to operate the equipment.

TROUBLESHOOTING

If there is no LCD display and/or LED signal light

feedback of CLIPSULIN

, please follow the steps below:

Check if there is any physical damage to the

CLIPSULIN

. If yes, stop using the device and

replace it with a new one. If no, check the LCD

and LED functions.

If only the LCD display OR the LED signal light

is not functioning, stop using the CLIPSULIN

and

replace it with a new one.

If both the LCD and LED are not functioning

properly, replace the battery and check both

functions again.

Caution: After replacing the battery, before using

the CLIPSULIN

with your insulin pen, sync the

CLIPSULIN

with the DIABNEXT

APP to adjust its time.

If the problem persists, go to customer service.

(www.diabnext.com/Q&A)

If the CLIPSULIN

cannot connect with the

DIABNEXT

APP, please follow the steps below:

Check if there is any physical damage to the

CLIPSULIN

. If yes, stop using the device and

replace it with a new one.

If no, reboot the Bluetooth/NFC function on the

mobile device, and then try to connect with the

CLIPSULIN

again.

If rebooting the Bluetooth/NFC function does not

resolve the issue, reinstall the DIABNEXT

APP,

then try to connect with the CLIPSULIN

again.

If the problem persists, go to customer service.

(www.diabnext.com/Q&A)

If the injection data cannot be transferred to the

DIABNEXT

APP, please follow the steps below:

Check if there is any physical damage to the

CLIPSULIN

. If yes, stop using the device and

replace it with a new one.

If no, reboot the Bluetooth/NFC function on the

mobile device, and then try to connect with the

CLIPSULIN

again.

If rebooting the Bluetooth/NFC function does not

resolve the issue, reinstall the DIABNEXT

APP,

then try to connect with the CLIPSULIN

again.

If the problem persists, go to customer service.

(www.diabnext.com/Q&A)

If you see the "Device error, please contact customer

service" message pop up in your APP, please follow

the steps below:

When this message pops up, it means that

some records in the memory might be

damaged.

Please conﬁrm the message and go to customer

service.

(www.diabnext.com/Q&A)