Cygolite TridenX 1300 Xtra Manuel d'utilisation - Page 2

Parcourez en ligne ou téléchargez le pdf Manuel d'utilisation pour {nom_de_la_catégorie} Cygolite TridenX 1300 Xtra. Cygolite TridenX 1300 Xtra 2 pages. Triple led rechargeable smart bicycle light

Imprimer la page

HEADLIGHT OPERATION

The TridenX features a BICYCLING MODE with 4 brightness mode, and a

SPECIAL MODE with 3 flashing, and a walking mode. These modes are

controlled by the power button and OSP button on the top of the headlight.

On top center of the headlight are 4 indicators that show which setting the

headlight is in with the rear indicator also functioning as a battery level

indicator. The diagram and instructions below indicate where these features

are located on the headlight and how to properly use them.

CAUTION: The light may get hot during use. Handle with care and turn

light off if stationary for more than 10 minutes.

OSP BUTTON

BATTERY LEVEL

INDICATOR

BICYCLE MODE (4)

Boost >High > Med > Low

SteadyPulse > Day Flash > Slow Flash > Walking

Turn ON

PLUG battery cable

into headlight DC Jack

PRESS power button for 2 seconds

(or from off position)

PRESS Power button

Switch

PRESS Power button to scroll between modes

mode

Customize

Press and hold OSP button to gradually change brightness (in Special

mode

mode flash speeds change) and RELEASE the button to stop the change.

HOLD the button again to change brightness in the opposite direction. If

brightness does not change while holding, the light reached the upper or

lower limit, RELEASE and HOLD the button again to go the opposite

direction.

Turn OFF

HOLD Power button for 2 seconds

CUSTOMIZE LIGHT SETTINGS

OSP is the first smart technology by Cygolite that gives you the freedom

to customize your preferred brightness settings and flashing speeds directy

to your headlight anytime, anywhere. You can use the factory default

settings or use the OSP button to customize your preferred settings.

NOTE: Boost mode and Walking mode are non-adjustable.

WARNING: Use discretion when programming the TridenX while riding. Do

not program your light during times that require total attention. Cygolite

cannot be held responsible for injuries that may occur during riding.

TO RESTORE FACTORY DEFAULT SETTINGS

While the light is ON, press and HOLD the power button for 7 seconds. The

light will turn off, then turn back on with the factory default settings.

THERMAL PROTECTION

The TridenX features a built in thermal protection to prevent the light from

overheating. The thermal protection will automatically dim the light (approx. 15%

brightness reduction) until the light cools to a normal operating temperature. At

that time, the light will return to its normal brightness.

LIGHT MODE INDICTORS

The 4 illuminated LEDs on the top of the headlight show which setting is in use.

INDICATOR

top of headlight

BICYCLE Mode

SPECIAL Mode

BATTERY LEVEL INDICATOR

The battery level indicator is the blue LED closest to the back of the light next

LIGHT MODE

to the power button. It flashes 3 different speeds to indicate the battery levels.

INDICATORS

Indicator

Flash sequence

Indicator

POWER BUTTON

(top of headlight)

Power In

DC JACK

TridenX Xtra

(time remaining)

TridenX

SPECIAL MODE (4)

(time remaining)

(From off position)

MOUNTING ON HANDLEBARS

and then release

Spacers

1. Attach handlebar spacers to inside of handlebar bracket for standard

sized and remove them for oversized handlebars.

2. Swing thumbnut down from thumbnut slot to open bracket.

3. Attach rubber pad to handlebar spacer. First remove paper from

rubber pad to reveal adhesive side, align rubber pad holes to

handlebar spacer plugs and join together.

4. Wrap bracket around handlebar & return thumbnut to slotted space.

5. Twist thumbnut clockwise until tight.

6. Slide headlight downward into bracket until headlight clicks into place.

TO REMOVE HEADLIGHT FROM THE HANDLEBARS

1. Press tab on bracket plate forward.

2. Slide headunit up.

TO ADJUST THE SIDE-TO-SIDE BEAM DIRECTION

Roll the headlight left to right to adjust the side-to-side direction.

MOUNTING BATTERY

The TridenX comes with a stem mount battery (standard model) or a frame

mount battery (Xtra model). Attach battery to the bike as followed:

Add Foam Pad

HIGH

MEDIUM

BOOST

DAY FLASH

WALKING

S.PULSE

SLOW FLASH

Constant

Fast Flash

Slow Flash

with Blink

Full to

Less than

1-1/2 hour left

1/2 hour left

1-1/2 hour left

Full to

Less than

3/4 hour left

1/4 hour left

Rubber Pad

Velcro Slot

Stem mount

3 A

1. An adhesive foam pad is included to provide cushion and grip between

the battery and the bike.Apply the foam padding to the center of the

battery above the velcro slot.

2. Thread the velcro strap through the velcro slot

3A (Stem mount). Wrap velcro strap around stem, through plastic loop,

and fasten to itself

3B (Frame mount). Wrap velcro strap around frame, through plastic loop,

and fasten to itself

LOW

BATTERY MOUNTING PRECAUTIONS: When mounting the battery to the

bike, make sure the battery cable and battery velcro strap do not interfere

with the brake cables or the ability to turn the handlebars.

HELMET MOUNTING

The TridenX can be mounted on the helmet with the included helmet mount kit.

Refer to separate helmet mounting instruction that is included with the helmet

mount kit.

BATTERY CHARGING

Headlight

flashes for

NOTE: Give the battery a full charge before using for the first time. To prolong

20 seconds

battery life, give the battery a 1 hour charge every 2 months it is not being used.

then turns off

1. Connect the charger to wall outlet first then the battery to the charger

(Follow sequence for proper charging.)

NOTE: The LED charging indicator on charger may take up to 30 seconds to

Battery

turn on after the battery and charger have been connected.

Empty

2. The LED on the wall charger shows red when charging then

green when fully charged.

3. Allow approx. 4-8 continuous hours to fully charge a drained battery.

4. Disconnect charger and battery when charging is complete and not in

use.

Allow approximately: 4 hours to fully charge (stem mount battery)

: 8 hours to fully charge (frame mount battery)

LED charging indicator

RED=Charging

GREEN=Fully charged

Outlet

Wall charger

WARNING: Charge the battery with the supplied charger only. Using any

other charger to charge the battery may result in damage. The Smart

Rapid charger is for indoor use only. Unplug the battery, and charger

once the battery is fully charged.

RUN TIMES

The run times below are based on the factory default settings. Run times

will vary if you customize the light settings.

BICYCLE MODE

(lumen)

Boost

(1300)

High

(900)

Medium

(650)

Low

(150)

SPECIAL MODE

SteadyPulse*

Frame mount

Day Flash

Slow Flash

Walking

NOTE: *SteadyPulse mode combines steady brightness to see and

alerting flash to be seen into one mode. It is made especially for riding at

night in high traffic areas.

Battery

TridenX 1300 Xtra

TridenX 1300

RUN TIME* (hr: min)

3:30

1:45

2:30

3:30