Closer pets 472 Instructions

Parcourez en ligne ou téléchargez le pdf Instructions pour {nom_de_la_catégorie} Closer pets 472. Closer pets 472 2 pages.

Imprimer la page

5000

7000

9000

Ref. 472, 473, 474

IMPORTANT SAFETY

INSTRUCTIONS

WARNING - To guard against

injury or death, basic safety

precautions should be

observed, including the

following:

READ AND FOLLOW

ALL SAFETY

INSTRUCTIONS

• Register

your

purchase

on-line

www.closerpets.com

guarantee overleaf).

• All electrical work must be carried out

by a competent electrician.

• Check that the voltage label on the

motor conforms with your supply

voltage.

• The pump MUST be wired into a

ground

fault

circuit

interrupter

(G.F.C.I.) maximum 30mA and a

3 AMP (maximum) fuse.

• Connection to the power supply

should be made through a double pole

switched enclosure with minimum

(3mm) contact separation in all poles.

• This appliance must be earthed. It

is essential that all connections are

securely made using the following

code:

Brown – Live

Blue – Neutral

Green/Yellow – Earth

• Do not carry or pull the pump using

the supply cord.

• Disconnect electrical supply from

all appliances in the pond including

pumps and filters before contact with

the pond water or pump.

• Maximum operation depth is 5ft

(1.5m).

• Do not use with water above 35℃.

• Closely supervise children when near

to pond or pond equipment.

• Use pump only for ponds - do not use

pump in connection with swimming

pools, showers, etc.

• Use conduit approved by your

electricity authority to protect supply

cord where damage from gardening

equipment, children and animals may

occur.

• Discard pump if motor shows visual

defects (e.g. cracks or swelling).

• The supply cord of this appliance

cannot be replaced; if the cord is

damaged the appliance should be

discarded.

• Do not allow the pump to run dry.

• Do not operate the pump in freezing

conditions. Remove, disassemble

and dry pump if there is a risk of

pump being frozen.

• This pump is provided with a thermal

cut-out

switch

that

temporarily

switches off the pump in case of

overheating. The pump may restart

when it has cooled.

SAVE THESE

INSTRUCTIONS

(see

1. PUMP INSTALLATION

Ideally and for convenience the pump should

be positioned within reach of the side of the

pond on a solid platform (e.g. paving slabs).

The pump must be at least 200mm (8") below

water level to avoid problems of freezing and

low water levels in summer.

All electrical work should be completed by a

qualified electrician.

Only use pump if completely immersed in

water.

A. Waterfall/Filter Only

For use with a pond filter you will often get

improved results with the pump sited at the

opposite end of the pond to the filter return.

The pump comes as standard with pond-life

friendly slots to help protect spawning life. In

some ponds this may not be necessary and you

may want to modify the pump to enable solids-

handling as below. The pump may be connected

to a waterfall or filter using 19mm (

(1") or 32mm (1

flow use 32mm (1

to the hose adaptor on the rotor cover.

The rotor assembly can be rotated through

90° as required by twisting the front end of

the pump.

B. Fountain (and Waterfall/Filter)

Insert fountain components as instructed in

Fountain Kit.

www.closerpets.com

Pond Pump · Instructions

IMPORTANT - READ BEFORE USE

"), 25mm

") bore hose. For maximum

") hose connected directly

Model

Voltage

472

220-230V 50HZ

473

220-230V 50HZ

474

220-230V 50HZ

2. MAINTENANCE / TROUBLESHOOTING

IMPORTANT SAFETY INSTRUCTIONS

• Disconnect electrical supply from pump

before removing from pond or contacting

pond water.

• Do not carry or pull the pump by the cable.

A. When flow from your pump is noticeably

reduced or fountain display has deteriorated:

i) Remove strainer cover by squeezing sides and

pulling off.

ii) Clean cover and remove any weed or blockage

around pump inlet rotor inlet.

iii) If you are using a fountain, remove and clean

fountain head in water with a brush.

iv) Reassemble. If flow is still poor check to see if

outlet pipe has become kinked or blocked.

B. If flow is stopped

i) Disconnect power.

ii) Remove cover and check for free rotation/

breakage of rotor.

iii) If rotor will not turn or is broken, remove and

clean - replace if broken or worn.

If in doubt please contact Closer Pets Customer

Service.

iv) Reassemble in reverse order after careful

cleaning of all components.

v) Replace the pump in water before reconnecting

power to start pump. If pump does not start

or stops again please contact Closer Pets

Customer Service.

Power (W)

Flow Rate

Lift (M)

5000 L/H

6500 L/H

8500 L/H

+44 (0)1932 700 001

47203/02

4.0

5.0

5.5