Ashly TRA-2150 Notes techniques et spécifications
Parcourez en ligne ou téléchargez le pdf Notes techniques et spécifications pour {nom_de_la_catégorie} Ashly TRA-2150. Ashly TRA-2150 2 pages. Tra-series
Également pour Ashly TRA-2150 : Spécifications (2 pages), Manuel d'utilisation (12 pages), Manuel d'utilisation (12 pages), Spécifications (2 pages), Manuel d'utilisation (13 pages)
TRA-Series 2075 and 2150 Two-Channel Amplifiers
Architects Specifications
TRA-Series, Lo-Z, 70/100V 2-Channel Amplifiers
The power amplifiers shall consist of two separate models (2075,
2150), being of two channels, and shall deliver a minimum power
of 40 or 80 watts RMS per channel into 8 ohm loads and 75 or
150 watts RMS per channel into 4 ohms depending on the model
being used. The amplifiers shall have internally mounted trans-
formers to provide both 70V and 100V constant voltage. Each
channel shall deliver a minimum of 75W or 150W, model depend-
ing, to the constant voltage lines.
Dimensions of the amplifiers shall be 19"W x 35"H x 11.0"D, with
a weight of 19.5 pounds. The amplifiers shall utilize a state-of-
the-art, efficient, switched mode power supply. The power supply
shall operate at either 120 or 240VAC, 50/60Hz. The amplifier
shall be convection cooled.
The amplifier shall have a selectable input gain of 26dB or 36dB.
Frequency response shall be 20 Hz - 20 kHz, +/- 1.0 dB. Hum
and noise shall be greater than 98dB below full output (20Hz to
20KHz unweighted).
Each amplifier channel shall be supplied with an attenuator
located on the rear panel. Each input shall have a fixed high pass
filter of 12dB/octave at 80Hz.
The inputs shall be active balanced design, with an impedance
of 20K ohm with a maximum input level of +21dBu. Input con-
nections shall be 3-pin Euroblock. Output connectors shall be a
screw terminal strip with safety cover.
The amplifiers shall have front panel indicators for power, stand-
by and protect. Each channel shall have a 6-step signal level
meter indicating -24db, -18dB, -12dB, -6dB, and -3dB and clip
alert.
The amplifier shall have built in protection for Output Over-
Current, DC Output, Main Supply Rail Overvoltage, Chassis
Internal Temperature, Inrush Limiting and Mains Fuse.
The amplifer shall have a 2-pin Standby Connector to provide
for remote standby switching with a 0.5 second turn-on delay.
Additionally, the amplifier shall have user selectable Delay
Switches to provide incremental turn-on delay when the Standby
connector is used. The switches shall be additive, providing as
much as 7.5 seconds of delay to the 0.5 second Standby delay.
The amplifier shall have a cTUVus safety listing and shall be in
compliance with FCC, CE and RoHS regulations.
The amplifier shall be covered under a full limited warranty of not
less than five years. The amplifier shall be an SRA-Series two-
channel model, manufactured by Ashly Audio, Inc. of Rochester,
New York.
Technical Notes & Specifications
Features
• 2RU Chassis
• High Efficiency Switched Mode Power
Supply
• Class-D Output Circuitry
• Input Attenuators On Rear Panel
• Input Sensitivity 26dB or 36db
• Remote Power Turn-On/Off
• Adjustable Turn-on Delay
• Convection Cooled
• 6-Step Signal Level and Clip LEDs
• Safety/Compliance: cTUVus/FCC,
CE, RoHS