Ashly MX-206 Manuel d'utilisation - Page 7

Parcourez en ligne ou téléchargez le pdf Manuel d'utilisation pour {nom_de_la_catégorie} Ashly MX-206. Ashly MX-206 12 pages. Stereo microphone mixer
Également pour Ashly MX-206 : Notes techniques et spécifications (2 pages), Manuel d'utilisation (8 pages), Manuel d'utilisation (9 pages), Manuel d'utilisation (12 pages)

Imprimer la page

Operator Manual – MX-206 Mixer

MX-206 Rear Panel

Power Switch - This switch turns on AC power

to the mixer, lighting the blue front panel LED. If

the switch is pressed but the LED is still off,

check to see that the AC power cord is not

detached.

Microphone Input - The microphone input is

an active balanced type with a nominal

impedance of 1200 ohms. Its noise

performance is best with a 200 ohm

microphone. The Mic input connector is a

standard 3-pin XLR female.

Input Pad - The Pad is a 20dB attenuation

switch on the rear panel for use with each XLR

microphone input. It should normally be left in

the "out" position for best signal to noise ratio

and should only be used when the input is

being overdriven with the Input dB (gain) switch

at its minimum setting.

Tape/CD Input - Tape Output - The stereo

inputs on RCA connectors have a nominal

operating level of -10dBu to match most tape

decks and CD players. The tape outputs are -

10dBu "premaster", so they are not affected by

the settings of the output controls.

Always switch the unit off before making substantial changes to the settings or connectors. Use

four screws and washers when rack mounting. This unit has specific electrical and signal

requirements, please take special care to double check all connections and settings and refer to

the specifications section of this manual. The unit should be connected to a standard 3-wire

grounded electrical outlet supplying 100-240 Volts, 50-60 Hz. To reduce the risk of ground

loop hum, connect all audio equipment to the same electrical power source. Removal of the

ground pin is both unlawful and dangerous, as a potential shock hazard could result. Overall

power consumption is less than 30 watts.

NOTE: The power switch does NOT isolate the appliance from mains. Make sure the mains

power socket or an alternative disconnect device is near by and easily accessible. When the

product is connected to mains, the line-filter and the input of the fuse are energized.

Mono Transformer Balanced Output - The

mono transformer output uses a male XLR

connector and provides total isolation for 600

ohm lines. The output is controlled by the Mono

level, with a nominal operating level of +4dBu.

Note: The transformer-balanced output is

designed to drive up to +24dBu into a 600 ohm

load. Because of the nature of an output

transformer, the output level increases as the

impedance of the terminating load becomes

higher than 600 ohms. Whereas a "direct-

coupled" output stage like that of the stereo

outputs will not change as the load changes,

any transformer used in an audio path is

affected by its termination impedance. Since

line level inputs on audio devices are typically

10K or higher, expect a slight increase

(2.5dB) in output level when driving high

impedance inputs with the mono. The output

meters will reflect the levels present on the

stereo outputs, regardless of the load on the

transformer output.

Stereo Outputs - The Stereo Outputs are

controlled by the left and right master. They are

1/4" balanced TRS jacks with a nominal

operating level of +4dBu into any load.

Page - 7

Safety Instructions – 3

Introduction - 4

MX-206 Mixer – 5

Connectors & Cables – 5

Physical Description - 6

Front Panel

Rear Panel

Installation – 7

Typical Applications - 8

Troubleshooting - 9

Dimensions - 9

Specifications - 10

Warranty - 11