Cypress Semiconductor CY7C1334H Fiche technique - Page 4

Parcourez en ligne ou téléchargez le pdf Fiche technique pour {nom_de_la_catégorie} Cypress Semiconductor CY7C1334H. Cypress Semiconductor CY7C1334H 14 pages. 2-mbit (64k x 32) pipelined sram with nobl architecture

Imprimer la page

Functional Overview

The CY7C1334H is a synchronous-pipelined Burst SRAM

designed specifically to eliminate wait states during

Write/Read transitions. All synchronous inputs pass through

input registers controlled by the rising edge of the clock. The

clock signal is qualified with the Clock Enable input signal

(CEN). If CEN is HIGH, the clock signal is not recognized and

all internal states are maintained. All synchronous operations

are qualified with CEN. All data outputs pass through output

registers controlled by the rising edge of the clock. Maximum

access delay from the clock rise (t

device).

Accesses can be initiated by asserting all three Chip Enables

(CE

, CE

) active at the rising edge of the clock. If Clock

Enable (CEN) is active LOW and ADV/LD is asserted LOW,

the address presented to the device will be latched. The

access can either be a Read or Write operation, depending on

the status of the Write Enable (WE). BW

conduct Byte Write operations.

Write operations are qualified by the Write Enable (WE). All

writes are simplified with on-chip synchronous self-timed write

circuitry.

Three synchronous Chip Enables (CE

asynchronous Output Enable (OE) simplify depth expansion.

All operations (Reads, Writes, and Deselects) are pipelined.

ADV/LD should be driven LOW once the device has been

deselected in order to load a new address for the next

operation.

Single Read Accesses

A read access is initiated when the following conditions are

satisfied at clock rise: (1) CEN is asserted LOW, (2) CE

and CE

are ALL asserted active, (3) the Write Enable input

signal WE is deasserted HIGH, and (4) ADV/LD is asserted

LOW. The address presented to the address inputs is latched

into the Address Register and presented to the memory core

and control logic. The control logic determines that a read

access is in progress and allows the requested data to

propagate to the input of the output register. At the rising edge

of the next clock the requested data is allowed to propagate

through the output register and onto the data bus, provided OE

is active LOW. After the first clock of the read access the output

buffers are controlled by OE and the internal control logic. OE

must be driven LOW in order for the device to drive out the

requested data. During the second clock, a subsequent

operation (Read/Write/Deselect) can be initiated. Deselecting

the device is also pipelined. Therefore, when the SRAM is

deselected at clock rise by one of the chip enable signals, its

output will tri-state following the next clock rise.

Burst Read Accesses

The CY7C1334H has an on-chip burst counter that allows the

user the ability to supply a single address and conduct up to

four Reads without reasserting the address inputs. ADV/LD

must be driven LOW in order to load a new address into the

SRAM, as described in the Single Read Access section above.

The sequence of the burst counter is determined by the MODE

input signal. A LOW input on MODE selects a linear burst

mode, a HIGH selects an interleaved burst sequence. Both

burst counters use A0 and A1 in the burst sequence, and will

wrap around when incremented sufficiently. A HIGH input on

ADV/LD will increment the internal burst counter regardless of

Document #: 38-05678 Rev. *B

) is 3.5 ns (166-MHz

can be used to

[A:D]

, CE

) and an

, CE

the state of Chip Enables inputs or WE. WE is latched at the

beginning of a burst cycle. Therefore, the type of access (Read

or Write) is maintained throughout the burst sequence.

Single Write Accesses

Write accesses are initiated when the following conditions are

satisfied at clock rise: (1) CEN is asserted LOW, (2) CE

and CE

are ALL asserted active, and (3) the write signal WE

is asserted LOW. The address presented to the address inputs

is loaded into the Address Register. The write signals are

latched into the Control Logic block.

On the subsequent clock rise the data lines are automatically

tri-stated regardless of the state of the OE input signal. This

allows the external logic to present the data on DQs and

DQP

. In addition, the address for the subsequent access

[A:D]

(Read/Write/Deselect) is latched into the Address Register

(provided the appropriate control signals are asserted).

On the next clock rise the data presented to DQs (or a subset

for Byte Write operations, see Write Cycle Description table for

details) inputs is latched into the device and the write is

complete.

The data written during the Write operation is controlled by

signals. The CY7C1334H provides Byte Write

[A:D]

capability that is described in the Write Cycle Description table.

Asserting the Write Enable input (WE) with the selected Byte

Write Select (BW

) input will selectively write to only the

[A:D]

desired bytes. Bytes not selected during a Byte Write

operation will remain unaltered. A synchronous self-timed

write mechanism has been provided to simplify the Write

operations. Byte write capability has been included in order to

greatly simplify Read/Modify/Write sequences, which can be

reduced to simple Byte Write operations.

Because the CY7C1334H is a common I/O device, data

should not be driven into the device while the outputs are

active. The Output Enable (OE) can be deasserted HIGH

before presenting data to the DQs. Doing so will tri-state the

output drivers. As a safety precaution, DQs are automatically

tri-stated during the data portion of a Write cycle, regardless of

the state of OE.

Burst Write Accesses

The CY7C1334H has an on-chip burst counter that allows the

user the ability to supply a single address and conduct up to

four Write operations without reasserting the address inputs.

ADV/LD must be driven LOW in order to load the initial

address, as described in the Single Write Access section

above. When ADV/LD is driven HIGH on the subsequent clock

rise, the Chip Enables (CE

, CE

ignored and the burst counter is incremented. The correct

inputs must be driven in each cycle of the burst write

[A:D]

in order to write the correct bytes of data.

Sleep Mode

The ZZ input pin is an asynchronous input. Asserting ZZ

places the SRAM in a power conservation "sleep" mode. Two

clock cycles are required to enter into or exit from this "sleep"

mode. While in this mode, data integrity is guaranteed.

Accesses pending when entering the "sleep" mode are not

considered valid nor is the completion of the operation

guaranteed. The device must be deselected prior to entering

the "sleep" mode. CE

, CE

, and CE

for the duration of t

after the ZZ input returns LOW.

ZZREC

CY7C1334H

, CE

, and CE

) and WE inputs are

, must remain inactive

Page 4 of 13

[+] Feedback