American Sensor CB100 Buku Petunjuk

Jelajahi secara online atau unduh pdf Buku Petunjuk untuk Alarm Asap American Sensor CB100. American Sensor CB100 2 halaman. Relay module

Halaman Cetak

This manual contains instructions for installing your

American Sensors

relay module. The relay module is ULC

listed as an accessory for use only with American Sensors

interconnectable smoke alarms in the 470L, 670L and 770L

series, plus models SA360, SA379, ESA5011 and combina-

tion CO/Smoke alarm model COS2010.

WARNING:

This relay will not operate without continuous

AC power. Do not use with battery backup units.

CAUTION:

Do not interconnect Model No. CB100 to any

other manufacturer's units.

RATING:

120VAC, 100mA

The CB100 relay module should be installed in a junction

box. All connections should be made by a qualified

electrician in accordance with the requirements of the

National Electric Code and/or any local codes having juris-

diction.

1. Turn off main power circuit.

2. Install and wire your compatible American Sensors

smoke alarm as recommended in your smoke alarm

owner's manual.

3. Connect the black wires of the relay module and the

smoke alarm to the black wire of the 120 VAC line.

4. Connect the interconnect wires as described below:

Your American Sensors

figured to allow it to operate for either a CO alarm condition

only, a smoke alarm condition only or for both CO and

smoke alarm conditions.

To Operate For A Smoke Alarm Condition Only:

See Fig. 1a and 1b on reverse.

Connect orange interconnect wire of the CB100 to the

orange interconnect wire of your smoke alarm (or to the

orange and brown wires of your CO/Smoke alarm).

To Operate Relay For A CO Alarm Condition Only:

See Fig 2 on reverse.

Connect brown interconnect wire of the CB100 to the

orange and brown wires of your co/smoke alarm and

orange wire of interconnected smoke alarms.

To Operate Relay For Both Smoke Alarm And CO

Alarm Conditions:

See Fig. 2 on reverse.

Open the green jumper wire on the CB100 and isolate

each end using a wire nut. Connect the brown intercon-

nect wire of the CB100 to the orange interconnect wire of

your smoke alarm and to the orange and brown wires of

your CO/Smoke alarm.

RELAY MODULE

INSTRUCTION MANUAL

INSTALLATION INSTRUCTIONS

CB100 relay module is easily con-

Use Your Relay Module For:

Sirens/Exit Signs/Bells

Warning Lights/Fire Doors/Exhaust Fans

Visual Indicators

CAUTION:

THE RELAY MODULE IS NOT TO BE USED

AS A METHOD OF EXTENDING THE MAXIMUM NUM-

BER OF SMOKE ALARMS PERMITTED IN MULTIPLE

STATION OPERATION. (REFER TO SMOKE ALARM

MANUAL FOR SPECIFIED MAXIMUM LIMIT.) EACH

RELAY MODULE REPLACES ONE SMOKE ALARM

LOAD IN AN INTERCONNECTED STRING. THEREFORE:

USE OF THE RELAY REDUCES THE MAXIMUM NUM-

BER OF INTERCONNECTED SMOKE ALARMS BY ONE.

5. Connect the white wires of the relay module and the

smoke alarm to the white wire of the 120 VAC line.

6. Connect the auxiliary device to the relay module

contact leads as required. Both normally open and

normally closed contacts are available to control the

auxiliary device.

7. Cap any unused leads with a wire nut.

8. Insert the relay module into the junction box and install

the faceplate.

9. Apply power to the circuit and test the smoke alarm

and the auxiliary relay device for proper operation.

This product is listed by

UNDERWRITER'S LABORATORIES OF

CANADA and Bears the Mark.

Dicon Global Inc.

88B East Beaver Creek Road, Unit 6,

Richmond Hill, Ontario, Canada L4B 4W2

Tel: 905-482-3720

info.diconglobal.com

MODEL NO. CB100

MODEL

NO.

CB100

MODEL

NO.

CB100

Fax: 905-731-8267

Page 1

2502-A0032REVA