Euro-Pro B20301 Panduan Pemilik - Halaman 3

Jelajahi secara online atau unduh pdf Panduan Pemilik untuk Penyedot Debu Euro-Pro B20301. Euro-Pro B20301 6 halaman. Cyclonic bagless upright

Halaman Cetak
Euro-Pro B20301 Panduan Pemilik
OPERATING INSTRUCTIONS
Changing the Headlight Bulb
Warning: To reduce the risk of electric
shock, the power cord must be
disconnected before removing the dust
cup, HEPA filter,changing the filters or
performing maintenance/trouble shooting
checks.
1. Turn unit "Off" and unplug from wall
outlet.
2. With a flat head screw driver, snap
off the lens cover by pressing down
on the two notches on the lens
cover. (Fig. 23)
3. Lift off the head light lens.

PROBLEM SOLVING

This appliance was inspected thoroughly and was in good operating condition when it
was shipped from the factory. If a minor problem occurs, it usually can be solved quite
easily when the cause is found. Therefore, this checklist is provided for your
convenience.
PROBLEM
POSSIBLE CAUSE
1.
Not properly plugged into wall
outlet.
Cleaner Won't
2.
No electricity in wall outlet.
Run
3.
On/Off switch not turned on.
4.
Motor thermostat tripped.
5.
Blown fuse/tripped breaker.
1.
Full or clogged dust cup.
2.
Wrong pile height setting.
3.
Clogged nozzle.
Cleaner Won't
4.
Clogged dust inlet port.
Pick Up
5.
Clogged hose.
6.
Broken belt.
7.
Hose not inserted fully.
8.
Dirty filters.
Cleaner Picks Up
Moveable Rugs
1.
Wrong pile height setting.
Or Pushes Too
Hard
Agitator Does Not
1.
Broken belt.
Turn
2.
Belt installed incorrectly.
Air Flow
1.
Attachment use restricts air
Restricted With
flow.
Attachment Use
2.
New carpet debris clogging
Sound Changes
air path.
Fig. 23
4. Remove the light bulb by pulling it
out carefully.
5. Replace the new bulb by pushing
it in.
6. Replace the head light lens by
pushing it in so that it snaps back in
place.
POSSIBLE
1.
Plug in firmly.
2.
Check fuse or breaker.
3.
Push on/off switch to on
4.
Reset motor thermostat.
(page 8 )
5.
Reset circuit breaker or replace fuse.
1.
Clean dust cup. (page 5)
2.
Adjust setting. (page 5)
3.
Remove obstruction.
4.
Remove power head cover and
remove obstruction.
5.
Remove obstruction.
6.
Replace belt. (page 8)
7.
Push hose in securely.
8.
Clean / change filters.
(page 6, 7)
1.
Adjust setting. (page 5)
1.
Replace belt. (page 8)
2.
Check belt changing and agitator
cleaning. (page 9)
1.
Check attachment.
2.
Remove obstruction.
9
Important:
If the suction opening in the unit, the hose or the extension tube become
blocked, switch off the vacuum cleaner and remove the blocking
substance before you start the unit again.
Notches
1.
Do not operate the vacuum
cleaner to close too heaters,
or radiators.
2.
Before inserting the power plug
into the wall outlet, make sure that
your hands are dry.
3.
Do not vacuum any liquids.
4.
Keep hair, loose clothing, fingers,
feet and all parts of body away from
openings, rotating agitator and other
moving parts.

PRECAUTIONARY MEASURES

5.
When pulling out the power plug
from the wall outlet, pull the plug
not the power cord.
6.
Do not pick up anything that is
burning or smoking such as
cigarettes, matches or hot ashes.
7.
Do not run appliance over power
cord.
8.
Do not use without dust cup
filter or filters in place.
9.
Before you start vacuuming,
make sure to remove large or
sharp objects that might
damage the vacuum.
2