Euro-Pro Shark SC505 Panduan Pemilik - Halaman 6

Jelajahi secara online atau unduh pdf Panduan Pemilik untuk Pembersih Uap Euro-Pro Shark SC505. Euro-Pro Shark SC505 6 halaman. Portable steam cleaner

Euro-Pro Shark SC505 Panduan Pemilik
OPERATING INSTRUCTIONS
How To Assemble & Use
IMPORTANT:
Always insure that the
unit is "UNPLUGGED" from the wall
receptacle prior to initial filling or re-filling
the water tank. Never attempt to fill this
unit under a water tap, always use the
filling flask provided. Failure to follow
these steps will cause the water tank to
overfill and may pose an electrical safety
hazard.
Step 1: Before filling the steam cleaner,
make sure that the unit is NOT
plugged in.
Step 2: Press locking trigger to ensure
all internal pressure is released.
Step 3: Turn Safety Cap counter
clockwise until removed.
Step 4: Release locking trigger.
Step 5: Add 28 fl. oz (800 cc) of water
using the filling flask provided.
Do not overfill. Replace
Safety Cap by turning
clockwise - press down firmly to
tighten. Heating time is
approximately 6 minutes. Filling
the boiler with hot water will
shorten heat up time.
Step 6: Plug the unit into a standard
120 volt grounded wall
receptacle. The power "On"
light (Red) will light up.
Step 7: Allow approximately 6 minutes
for water vapor to reach its
working temperature and
pressure. When unit is ready
for use the red light will change
to Green.
Step 8: At the start, some water will
come out from the nozzle. This
is normal.
NOTE: Disconnect steam cleaner from
wall outlet before refilling. It is time to refill
your steam cleaner when there is no more
steam coming out of the nozzle. Because
the water tank is pressurized, use caution
when opening to refill. Depress the trigger
button while you unscrew the safety cap
counterclockwise. Always let unit cool for
5 minutes before refilling the unit with
water.
CAUTION: When refilling the
appliance while it is still hot, the
first drops of water might
bubble up.
Using the Locking Trigger Button
The steam cleaner has a locking trigger
button. The trigger will lock when you
have pushed it in all the way. To unlock
the steam trigger, just press the locking
trigger button in and the steam trigger
will pop up, stopping the flow of steam.

Refilling With Water

Step 1: Disconnect electrical power
cord from wall outlet.
Step 2: Press trigger button until all
pressure has been released.
Step 3: Allow the unit to cool for
approximately 5 minutes
before refilling with water.
Carefully unscrew safety cap.
Step 4: Slowly pour water using the
filling flask into the boiler.DO
NOT Fill Under a faucet, use
the filling flask provided. DO
NOT OVERFILL. Always
leave approximately 2 1/2
inches between the top of
the unit and the water level.
Step 5: Release the locking trigger.
Step 6: Screw safety cap back on the
appliance and plug appliance
back into wall outlet. Steam will
start to be produced as before.
WARNING: This appliance is
under pressure. After every use,
press trigger button until all
pressure has been released
before removing safety cap.
Allow unit to cool for five (5)
minutes before refilling.
5
OPERATING INSTRUCTIONS cont.
ATTACHMENTS
Angle Concentrator/Brush Adapter
To attach the angle concentrator/brush
adapter to the hose, hold the hold grip in
one hand and insert the angle
concentrator/brush adapter into the nozzle
end of the hand grip. Make sure that it
locks in place. (See below.)
Using Accessories
To use the nylon detail brushes, attach the
nylon bristle brush to the end of the angle
concentrator/brush adapter. (See below.)
Window Squeegee
CAUTION: When cleaning
windows, always avoid any sudden
changes in temperature to prevent
glass breakage or cracks.
Please note that the window squeegee can
only be used with the
hose. To attach the
window squeegee to
the hose, push it in until
the squeegee locking
button clicks in place on
the hose.
Apply steam abundantly,
rub with the soft spongy end, then remove
excess water and dirt with the glass wiping
edge.
This attachment is very useful for cleaning
large windows, plastic material, ceramic,
tiled or marble surfaces.
Using the Steam Cleaner with
Floor Brush
Step 1: Connect one of the extension
tubes to the hand grip on the
flexible steam hose. To
attach the extension tubes
one onto the other or
onto the hand grip, press the
locking button ensuring that it
fits into the hole. (See
illustrations.) To disconnect,
repeat the operation by
pressing the locking button
and pulling the two sections
apart.
Extension Tubes
NOTE:
Fit floor brush with
the floor brush
angle adapter
on to the
Floor Brush
extension tube.
Angle Adapter
Step 2: If the floor brush angle adapter
is not attached to the floor
brush, hold the brush with its
bristles up in your left hand.
With the floor brush angle
adapter pointing downward,
insert it into the hole in the back
of the brush, then turn the floor
brush angle adapter 180°.
Step 3: Insert the electrical power cord
into the wall outlet. Heating
time is approximately 6 minutes
with cold water. Filling the
steam generator with hot water
will shorten heat up time.
6