American Standard 4099.700 Lembar Spesifikasi

Jelajahi secara online atau unduh pdf Lembar Spesifikasi untuk Perabotan Dalam Ruangan American Standard 4099.700. American Standard 4099.700 1 halaman. American standard elongated pressure-assisted toilet specification sheet

YORKVILLE™ ELONGATED
PRESSURE-ASSISTED TOILET
2320.101
• Vitreous china
• Low-consumption (6.0 Lpf/1.6 gpf)
• Floor-mounted, back-outlet toilet
• Elongated bowl
• Pressure-assisted siphon jet flush action
• Side-mounted chrome trip lever
• Close-coupled flushometer tank*
• Speed Connect
tank/bowl coupling system
®
• 4 bolt caps
• Fully glazed 2" ballpass trapway
• 10" x 12" water surface area
• 100% factory flush tested
3120.019 Elongated bowl with four bolt
caps and two floor screws
4099.100 Flushometer tank complete with
coupling components
Component parts:
735084-400 Tank cover (specify color)
Nominal Dimensions:
813 x 495 x 749mm
(32" x 19-1/2" x 29-1/2")
Alternate Configurations:
4099.700 Tank and tank cover only
with tank cover locking device
4099.800 Tank and tank cover only
with right hand trip lever
Fixture only, seat and supply by others
Recommended working pressure range 20 psi - 80psi
Compliance Certifications -
Meets or Exceeds the Following Specifications:
• ASME A112.19.2 for Vitreous China Fixtures
To Be Specified:
❏ Color: ❏ White ❏ Bone ❏ Linen
❏ Silver ❏ Fawn Beige
❏ Seat: American Standard #5324.019
Elongated "Rise and Shine" (with easy to clean
lift-off hinge system) solid plastic closed front
seat with cover.
❏ Seat: American Standard #5325.024
Elongated "Rise and Shine" (with easy to clean
lift-off hinge system) solid plastic open front
seat with cover.
❏ Alternate Seat:
❏ Supply with Stop:
* Flushmate III tank system by Flushmate
© 2008 AS America Inc.
❏ Black
®
Div. of Sloan Valve Co
YORKVILLE™ ELONGATED
PRESSURE-ASSISTED TOILET
Replaces 2320.100
FINISHED WALL
813mm
(32)
19mm ± 6mm
(3/4 ± 1/4)
279mm
(11)
470mm
(18-1/2)
C/L OF SEAT
POST HOLES
140 mm (5-1/2)
CENTER
*
222mm
(8-3/4)
C/L OF 1/2" DIA HOLES
324mm
152mm (6) CENTERS
(12-3/4)
648mm
(25-1/2)
NOTES:
WASTE OUTLET SEAL RING MUST BE NEOPRENE OR GRAPHITE-
FELT (WAX RING NOT RECOMMENDED).
SUPPLY NOT INCLUDED WITH FIXTURE AND MUST BE ORDERED
SEPARATELY.
*
DIMENSION SHOWN FOR LOCATION OF SUPPLY IS SUGGESTED.
FOR ADDITIONAL INFORMATION REFER TO INSTALLATION
INSTRUCTIONS SUPPLIED.
IMPORTANT: Dimensions of fixtures are nominal and may vary within
the range of tolerances established by ANSI Standard A112.19.2. These
measurements are subject to change or cancellation. No responsibility is
assumed for use of superseded or voided pages.
M43
VITREOUS CHINA
495mm
(19-1/2)
C/L
381mm
(15)
FLEX
SUPPLY
356mm
AS REQ.
(14)
102 mm
152 mm
(4)
(6)
76mm
(3)
C/L OF
WASTE
235mm
OUTLET
(9-1/4)
Revised 2/08
749mm
(29-1/2)
13 x 19mm
(1/2 x 3/4)
SLOTS
76mm
(3)
FINISHED
FLOOR