Da-Lite ADVANTAGE ELECTROL Buku Instruksi - Halaman 11
Jelajahi secara online atau unduh pdf Buku Instruksi untuk Layar Proyeksi Da-Lite ADVANTAGE ELECTROL. Da-Lite ADVANTAGE ELECTROL 16 halaman. Tensioned large
Juga untuk Da-Lite ADVANTAGE ELECTROL: Buku Instruksi (12 halaman), Buku Instruksi (12 halaman), Panduan Pemasang (2 halaman), Buku Instruksi (4 halaman), Buku Instruksi (12 halaman)
Halaman Cetak
Screen Adjustment
If your Advantage Electrol was ordered as a complete unit, the up and down limits were pre-set by Da-Lite. If your screen and roller
assembly was ordered separately from the case, or if general adjustment is needed, please follow the steps below and refer to the
Wiring Diagram.
1.
Locate the wall switch and remove the cover plate from the
wall switch and remove the switch from the junction box.
2. Locate the two tactile buttons on the back of the switch.
They are black round buttons on silver plates.
3. To adjust the down limit switch, press and hold the down
tactile button until the LED on the back of the switch turns
solid red. This will put the motor in limit set mode. Turn the
wall switch over and use the down button on the front of the
switch. Press and hold the down button until the desired
down position is reached. If you travel too far down, press the
up button to move the screen upward. If you press and let go
of either the up or down buttons, the motor will do a small
jog in that direction for fine adjustment of the screen. Once
the desired position is reached, turn the switch over; press
and hold the down tactile button until the LED on back of
switch blinks red twice. The down limit is now set.
NOTE: If the screen is in limit set mode and no buttons are
pushed for 20 seconds, the LED on the back of the wall
switch will turn off, the motor will return to run mode and no
changes will be saved. If this occurs, return to step 3 for down
limit adjustment or step 4 for up limit adjustment.
Up Limit
Tactile Button
U P
S T O P
D O W
N
Down Limit
Tactile Button
Front of Wall
Switch
4. To adjust the up limit switch, press and hold the up tactile
button until the LED on the back of the switch turns solid
green. This will put the motor in limit set mode. Turn the wall
switch over and use the up button on the front of the switch.
Press and hold the up button until the desired up position is
reached. If you travel too far up, press the down button to
move the screen downward. If you press and let go of either
the up or down buttons, the motor will do a small jog in that
direction for fine adjustment of the screen. Once the desired
position is reached, turn the switch over; press and hold the
up tactile button until the LED on back of switch blinks green
twice. The up limit is now set.
5. To test the limit switch settings, press and release the up or
down buttons on the switch to operate the screen.
6. Replace the switch and cover plate on the wall.
IMPORTANT NOTE: The wall switch is REQUIRED to make
any limit switch adjustments, even if a third party control
system is used. Therefore, it is advised to wire the switch or
U P
provide a 3-conductor connection that is accessible.
CAUTION: Do not adjust for more drop than what was
S T O
P
ordered. At least 1–1/2 wraps of fabric must remain on the
roller. This screen comes standard with 0" or 2" black at
D O
W N
the top. See the specification data sheet for details.
ATTENTION! N'effectuez pas de réglage pour obtenir un
déroulement supérieur à celui commandé. Au moins 1 à
1/2 tour de toile doit être maintenu sur le cylindre. Cet
écran est doté de série d'une bande noire supérieure de 0
cm (0 po) ou 5 cm (2 po). Consultez la fiche technique
pour plus de renseignements.
Back of
Wall Switch
LED
11