American Standard 721AA Petunjuk Instalasi Perawatan dan Pemeliharaan
Jelajahi secara online atau unduh pdf Petunjuk Instalasi Perawatan dan Pemeliharaan untuk Toilet American Standard 721AA. American Standard 721AA 13 halaman.
Halaman Cetak
INSTALLATION INSTRUCTIONS
CARE AND MAINTENANCE
Clean
Dual Flush Concealed Trapway
®
Right Height
, Elongated Model 721AA
®
Thank you for selecting American Standard - the benchmark of fine quality for over 100 years. To ensure this product is
installed properly, please read these instructions carefully before you begin. (Certain installations may require professional
help.) Also be sure your installation conforms to local codes.
CAUTION: PRODUCT IS FRAGILE. TO AVOID BREAKAGE AND POSSIBLE INJURY HANDLE WITH CARE!
!
NOTE: Pictures may not exactly define contour of china and components.
RECOMMENDED TOOLS AND MATERIALS
Putty Knife
Regular Screwdriver
Hacksaw
Wax Ring/Gasket
1
REMOVE OLD TOILET
a. Close toilet supply valve and flush tank completely. Towel or sponge remaining water from tank and bowl.
b. Disconnect and remove supply line. NOTE: If replacing valve, first shut off main water supply!
c. Remove old mounting hardware, remove toilet and plug floor waste opening to prevent escaping sewer gases.
d. Remove closet bolts from flange and clean away old wax, putty, etc. from base area.
NOTE: Mounting surface must be clean and level before new toilet is installed!
2
ROUGHING-IN DIMENSIONS:
NOTE: Distance from wall to closet flange centerline must be as listed below:
IMPORTANT:
Water supply on the wall is required at 2-1/4" or 8" from centerline of the toilet (see rough-in). First suggested
position is hidden behind the toilet. The geometry of the toilet gives space for this installation. The second suggested position
is next to the toilet. Between these two positions, the space for the supply between wall and toilet is limited to 4-1/2". In this
case, check your supply and hose dimensions.
RIGHT HEIGHT ELONGATED 2-PIECE TOILET
FINISHED
WALL
(191mm)
12"
(305mm)
IMPORTANT: Water supply on the wall is required at 2-1/4" or 8" from centerline of the toilet (see rough-in).
First suggested position is hidden behind the toilet. The geometry of the toilet gives space for this installation.
The second suggested position is next to the toilet. Between these two positions, the space for the supply
between wall and toilet is limited to 4-1/2". In this case, check your supply and hose dimensions.
Adjustable Wrench
Flexible Supply Tube
30-1/4"
(768mm)
8-3/4"
(221mm)
C/L OF SEAT POST
HOLES 5-1/2"
(140mm) CENTERS
18-1/2"
(470mm)
16-1/2"
(419mm)
7-1/2"
13-11/16"
(347mm)
FINISHED
FLOOR
P r o d u c t n a m e s l i s t e d h e r e i n a r e t r a d e m a r k s o f A S A m e r i c a , I n c .
© A S A m e r i c a , I n c . 2 0 1 3
15-3/4"
(399mm)
14"
(356mm)
SUPPLY
AS
30-7/8"
REQUIRED
(784mm)
(position 1 or
position 2)
2-1/4"
8"
(57mm)
5-1/2"
(204mm)
(140mm)
6"
(152mm)
12-3/16"
(309mm)
Sealant
Tape Measure
Closet Bolts
Carpenters Level
BACK VIEW
(for reference)
Certified by
IAPMO R&T
7 30 2 06 8 -10 0