American Standard Acrylux Builder Series 6030Y2A.102.XXX Petunjuk Instalasi

Jelajahi secara online atau unduh pdf Petunjuk Instalasi untuk Bak Mandi Air Panas American Standard Acrylux Builder Series 6030Y2A.102.XXX. American Standard Acrylux Builder Series 6030Y2A.102.XXX 2 halaman. Acrylux builder series (above floor rough)

American Standard Acrylux  Builder Series 6030Y2A.102.XXX Petunjuk Instalasi

INSTALLATION INSTRUCTIONS

Acrylux Builder Series (Above Floor Rough)
Model 6030Y2A.102.XXX
Model 6030Y2A.202.XXX
Thank you for selecting American Standard – the benchmark of fine quality for over 100 years. To ensure this product is installed properly, please
read these instructions carefully before you begin. Local building codes vary by location. Observe all local plumbing and building codes.

RECOMMENDED TOOLS AND MATERIALS

Tape Measure
Safety Glasses
6030Y2A.102.XXX
6030Y2A.202.XXX
1"
25mm
18"
457mm
30"
762mm
IMPORTANT:
• Allow tub to reach room temperature before installation.
• Read installation instructions carefully before starting project.
• Keep instructions for warranty information.
INSTALLATION INSTRUCTIONS
STEP 1. PREPARING ALCOVE
• Strip to bare studs.
• Alcove studs should be constructed as shown above.
• Floor must be clean, smooth, and level (check with level). Sub floor must
be installed as in the stud layout. Do not install tub on open floor joists.
• If required, cut hole in sub floor as shown above to accommodate drain.
STEP 2. INSTALLING TUB
• Trial fit tub in prepared alcove. With tub sitting flat on floor, check with
level on top of tub. Tub should be level from front-to-back and
side-to-side (Fig 1).
• A floor leveling compound (smooth mortar) or a similar quick-setting
compound specifically made for leveling floors may be used to fully
support and level base.
• After tub is leveled, if alcove is larger than tub, shim between tub and
studs to create a tight fit. Screw tub flange to studs (Fig. 2).
CLEANING
• Do not use any abrasive cleaners or metal scrapers.
• If drywall mud or plaster gets on your shower, it may be carefully removed
with a wooden scraper made from a piece of scrap wood.
• Adhesive may be removed with mineral spirits.
• Ideal cleaners are Soft Scrub Gel
WARNING:
Some cleaning products are not suitable for use. Read all labels carefully.
DO NOT USE if they say "not suitable for use with ABS, acrylic, or polystyrene.
P r o d u c t n a m e s l i s t e d h e r e i n a r e t r a d e m a r k s o f A S A m e r i c a , I n c .
© A S A m e r i c a , I n c . 2 0 0 8
Mortar Compound (optional)
Screws, 1" Flathead, Stainless
59-7/8"
1521mm
®
®
or Comet Gel
.
Pencil
Drill
19"
483mm
31-1/2"
800mm
FIGURE 1. Check to assure tub is level.
FIGURE 2. If necessary, shim between tub and studs
for tight fit and screw to each stud.
Saber Saw
Level
STUD LAYOUT:
The American Standard Acrylux Bathtub
will fit all standard 30" x 60" tub walls.
14"
10"
356mm
254mm
6"
152mm
Drain C L
Floor Cut Out
8"
6" x 10"
203mm
(152 x 254mm)
60"
1524mm
= stud location
LHO shown - Reverse for RHO
7542 8 3 -1 00 Re v. A