Ekinex EK-HH1-TP Manual - Halaman 4
Jelajahi secara online atau unduh pdf Manual untuk Pengontrol Ekinex EK-HH1-TP. Ekinex EK-HH1-TP 4 halaman. Controller for mixing group
Characteristics of the terminals
• screw clamping of conductors
• maximum cross section of conductor 2.5 mm² (single-
wire) or 1.5 mm² (multi-wire)
• recommended wire stripping approx. 6 mm
• torque max 0.8 Nm
Configuration and commissioning
Configuration and commissioning of the device require
the use of the ETS
(Engineering Tool Software) program
®
V4 or later releases. These activities must be carried out
according to the design of the building automation system
done by a qualified planner.
i
Note. The configuration and commissioning of KNX
devices require specialized skills. To acquire these
skills, you should attend the workshops at KNX cer-
tified training centers.
Configuration
For the configuration of the device parameters the corre-
sponding application program or the whole ekinex
duct database must be loaded in the ETS program. For
detailed information on configuration options, refer to the
application manual of the device available on the website
www.ekinex.com.
Application
Product
program
code
(## = release)
EK-HH1-TP
APEKHH1TP##.knxprod
Commissioning
For commissioning the device the following activities are
required:
• make the electrical connections as described above;
• turn on the bus power supply;
• switch the device operation to the programming mode
by pressing the programming pushbutton located on
the front side of the housing. In this mode of operation,
the programming LED is turned on;
• download into the device the physical address and the
configuration with the ETS
At the end of the download the operation of the device
automatically returns to normal mode; in this mode the
programming LED is turned off. Now the bus device is
programmed and ready for use.
Dimensions [mm]
144
POWER AUX
CLOSE
COM
OPEN
DO1
DO2
15
16
17
18
19
20
21
22
23
IN1
IN2
IN3
IN4
IN5
3
4
5
6
7
8
9
10
11
12
OK
ESC
EK-HH1-TP
Mixing group controller
Area
Line
Dev.
bus KNX
Marks
• KNX
• CE: the device complies with the Low Voltage Directi-
ve (2014/35/EC) and the Electromagnetic Compatibili-
ty Directive (2014/30/EC). Tests carried out according
®
Communica-
Group
tion objects
adressses
(max nr.)
(max nr.)
185
254
program.
®
70
5
25
20
20
DO3
24
25
+
AO1
-
13
14
L
N
1
2
to EN 50491-2:2010, EN 50491-3:2009, EN 50491-4-
1:2012, EN 50491-5-1:2010, EN 50491-5-2:2010, EN
50428:2005 +A1:2007 + A2:2009
Maintenance
The device is maintenance-free. To clean use a dry cloth.
It must be avoided the use of solvents or other aggressive
substances.
Disposal
Warning! Incorrect disposal of this product may
!
cause serious damage to the environment and hu-
man health. Please be informed about the correct
disposal procedures for waste collecting and pro-
pro-
cessing provided by local authorities.
Document
This datasheet refers to the release A1.0 of the ekinex
device EK-HH1-TP, and is available for download at www.
ekinex.com as a PDF (Portable Data Format) file.
Filename
STEKHH1TP_IT.pdf
Warning
• Installation, electrical connection, configuration and
commissioning of the device can only be carried out
by qualified personnel in compliance with the appli-
cable technical standards and laws of the respective
countries
• Opening the housing of the device causes the imme-
diate end of the warranty period
• In case of tampering, the compliance with the essen-
tial requirements of the applicable directives, for which
the device has been certified, is no longer guaranteed
ekinex
defective devices must be returned to the
®
manufacturer at the following address: EKINEX S.p.A.
Via Novara 37, I-28010 Vaprio d'Agogna (NO) Italy
Other informations
• The instruction sheet must be delivered to the end
customer with the project documentation
• For further information on the product, please contact
the ekinex
technical support at the e-mail address:
®
[email protected] or visit the website www.ekinex.
com
• Each ekinex
®
the label. The serial number can be used by installers
or system integrators for documentation purposes and
has to be added in each communication addressed to
the EKINEX technical support in case of malfunctio-
ning of the device
• KNX
and ETS
®
Association cvba, Brussels
© EKINEX S.p.A. The company reserves the right to make changes to this
documentation without notice.
4
At the end of its useful life the product
described in this datasheet is classified
as waste from electronic equipment
and cannot be disposed together with
the municipal undifferentiated solid
waste.
Device release
A1.0
device has a unique serial number on
are registered trademarks of KNX
®
®
Updating
03 / 2017