Ekinex EK-GL1-DL Manual

Jelajahi secara online atau unduh pdf Manual untuk Dimmer Ekinex EK-GL1-DL. Ekinex EK-GL1-DL 9 halaman. Dali 4-channel dimmer

Halaman Cetak

DALI 4-channel dimmer

Code: EK-GL1-DL

DALI bus device to be supplied with 12 / 24 / 48 Vdc. It

provides the dimming control function for LED sources, by

means for several commands: KNX pushbuttons or other

local command devices.

Description

The ekinex DALI 4-channel dimmer EK-GL1-DL allows

brightness control of dimmable LED sources by means

of several types of button. It can be connected by me-

ans of KNX (TP) pushbutton connected to a DALI / KNX

Gateway or via another device, directly connected to the

dedicated input, selectable from a normally open button,

0-10V analog input, 1-10V analog input and 10 kΩ poten-

tiometer. The device has an integrated DALI bus com-

munication module and requires a 12, 24 o 48 Vdc input

power supply.

Functional characteristics

• Constant voltage dimmer

• DALI bus command

• Number of channels: 4

• 4 local commands: N.O. pushbutton / analog input

0-10V / 1-10V / Potentiometer

• Controls: dimmer, dim to warm, tunable white, RGB,

RGBW

• Voltage outputs for R-L-C loads

• Typical efficiency > 95%

• Brightness adjustment up to full off (Dim to Dark)

• Minimum brightness level: 0.1% (1% in push)

• D-PWM Modulation

• Adjusting D-PWM frequency: 300 / 600 / 1200 Hz

• Adjusting output curve: Linear / Quadratic / Exponential

• Soft dimming regulation

• Soft start and soft stop

Datasheet STEKGL1DL_EN

Technical data

Inputs

• Input (constant voltage): 12 / 24 / 48 Vdc

• Supply voltage: min: 10,8 Vdc .. max: 52,8 Vdc

• Input current: 20 A max

• Power absorbed while awaiting command: <500 mW

Outputs

• Output voltage = input voltage

• Output current: max 5 A / channel, max 20 A total

• Nominal power @12V: 60 W / channel – 240 W total

• Nominal power @24V: 120 W / channel – 480 W total

• Nominal power @48V: 240 W / channel – 960 W total

• Thermal shutdown: 150 °C

Note: values for output current and nominal power

have to be intended as maximum values, depen-

ding on the ventilation conditions

Dimming

• Dimming frequency D-PWM: 300Hz – 600Hz – 1200Hz

• Dimming resolution D-PWM: 16 bit

• Dimming range D-PWM: 0.1-100%

Environmental conditions and other characteristics

• Operating temperature: -40 ° C ... + 60 ° C

• Storage temperature: - 40 ° C ... + 60 ° C

• Transport temperature: - 40 ° C ... + 60 ° C

• Relative humidity: 93% non-condensing

• Protection degree IP10 (device installed)

• Command & bus wiring: 1.5 mm

ded – 30/14 AWG

• Power & LEDs wiring: 2. 5mm

ded – 30/12 AWG

• Command & bus stripping: 6 mm

• Power and LEDs stripping: 7.5 mm

• Housing in plastic material

• Safety class II

• Weight 120 g

• Modular device 4 MU (1 MU = 18 mm)

• Dimensions 72 x 90 x 70 mm (LxHxP)

Protections

Il dispositivo è dotato delle seguenti protezioni:

• OTP Over temperature protection

• OVP Over voltage protection

• UVP Under voltage protection

• RVP Reverse polarity protection

• IFP Input fuse protection

• SCP Short circuit protection

• OCP Open circuit protection

• CLP Current limit protection

1) Thermal Protection on the output channel in case of high temperature. The thermal

intervention is detected by transistor (>150°C)

2) Control logic protection only

Control, signaling and connection elements

The device is equipped with a screw terminal for connec-

ting the 12 / 24 / 48 Vdc input power supply and the LED

output loads (1), a screw terminal for connecting the local

commands (2), a screw terminal for the DALI line connec-

tion (3) and one signaling LED (4).

solid – 1 mm

stran-

solid – 1.5 mm

stran-