American Time SiteSync IQ Panduan Instalasi Mulai Cepat - Halaman 2

Jelajahi secara online atau unduh pdf Panduan Instalasi Mulai Cepat untuk Jam American Time SiteSync IQ. American Time SiteSync IQ 2 halaman. Wireless clock system gps plus with ethernet & campus tx antenna
Juga untuk American Time SiteSync IQ: Panduan Instalasi dan Pengoperasian (2 halaman), Panduan Instalasi dan Pengoperasian (13 halaman), Panduan Instalasi dan Pengoperasian (7 halaman), Panduan Instalasi dan Pengoperasian (6 halaman), Panduan Instalasi Mulai Cepat (2 halaman), Panduan Instalasi Mulai Cepat (2 halaman), Panduan Instalasi Mulai Cepat (2 halaman), Panduan Instalasi Mulai Cepat (2 halaman), Panduan Instalasi Mulai Cepat (2 halaman), Panduan Instalasi Mulai Cepat (2 halaman), Panduan Memulai Cepat (2 halaman), Panduan Memulai Cepat (2 halaman), Panduan Memulai Cepat (2 halaman), Panduan Memulai Cepat (2 halaman)

Halaman Cetak

American Time SiteSync IQ Panduan Instalasi Mulai Cepat

QUICK START INSTALLATION GUIDE

Unpack the box

1. Remove the components and Remote Transmitter from the

box. Save the packing materials in case you need them later.

Check the components

Your system kit comes with:

• Remote Transmitter

• Power cord

(B)

• Magnetic mount TX antenna with 12' cable

• Installation and Operation Manual

Choose your location

• Locate the Remote Transmitter in an area with a network drop,

or run an Ethernet data cable to the unit from a network

switch or hub.

• Choose a location for your magnetic mount TX antenna either

outside or inside at the highest central location in your facility.

The TX antenna must be located at least 4' away from

the Remote Transmitter and must always point up or down,

never horizontal! The cable length cannot be extended.

4 ft

minimum

Remote Transmitter

located high & central

with Ethernet drop for

time reference

TX Ant signal

out to clocks

Connect cables to the Remote Transmitter

Connect a CAT 5 or higher Ethernet patch cable (not included)

to the ETHERNET RJ45 port.

Connect the power cord to the Remote Transmitter.

Connect mag mount antenna to the Antenna port. *Lightning

arrestor must be grounded per local electrical code.

Plug 110v cord into power source. Turn the POWER SWITCH on

the back of the Remote Transmitter to the on position.

(C)

Setup the Remote Transmitter

1. Record the last 6 digits of the Serial Number in the empty spaces

below. The Serial Number is located on the product label on the

bottom of the Remote Transmitter.

Host Name:

The Host Name is used to identify the Remote Transmitter on the network.

abcdefghijklmn

SITESYNC IQ

To local

power

(120vac)

Example Product Label

REMOTE TRANSMITTER

continued

2. The default Ethernet setting has DHCP enabled to automatically

obtain its TCP/IP network setting from a DHCP server. Launch your

web browser, and enter the above recorded host name

http://sqrtxxxxxx/ into the URL field of the web browser. Press the

Enter key. This will connect to the Remote Transmitter's

configuration utility Remote Transmitter Connect.

Note: If the Remote Transmitter is on a network without a DHCP

server the default address of the Remote Transmitter

will be 192.168.10.10.

Note: If a static IP is required for your network, reference the Remote

Transmitter Installation and Operation Manual.

3. Once you are connected to the Remote Transmitter a User Login

window will appear. Enter sclock in lowercase letters in the User

Name field and sclock in the Password field. This is the default

service login which will allow access to all menus. Then, click the

Note: Passwords may be changed in the Configuration Tab.

4. Click on the Set tab menu and verify the appropriate local time zone

from the drop down menu.

5. Daylight Saving Time default is set to AUTO. If your location doesn't

observe DST select drop down menu to OFF.

6. To confirm proper setup, enable the On Demand Sync Ethernet

button and press Sync Now. If successful a green check-mark will

appear next to the Sync Now button.

7. Verify the unit is transmitting. The PTT and Data LED's on the front

of the Remote Transmitter should flash every 30 seconds unless in

Quiet Mode.