QUICK START INSTALLATION GUIDE
1
Unpack the box
1. Remove the components and system controller from the box.
Save the packing materials in case you need them later.
2
Check the components
Your system kit comes with:
• System Controller
• Power supply
(B)
• Magnetic mount TX antenna with 12' cable
• USB Flash drive
• Installation and Operation Manual
3
Choose your location
• Locate the system controller in an area with a network drop,
or run an Ethernet data cable to the unit from a network
switch or hub.
• Choose a location for your magnetic mount TX antenna either
outside or inside at the highest central location in your facility.
The TX antenna must be located at least 4' away from
the system controller and must always point up or down,
never horizontal! The cable length cannot be extended.
System controller
located high & central
with Ethernet drop for
time reference
4
Connect cables to the system controller
A.
Connect a CAT 5 or higher Ethernet patch cable (not included)
to ETHERNET RJ45 port.
B.
Connect the System Controller power supply to the POWER
INPUT port.
C.
Connect the magnet mount TX antenna to the TX ANT port.
Plug 110v cord into power source. Turn the POWER SWITCH on
the back of the system controller to the on position.
Note: If your system controller supports more than one time sync
option, refer to the SiteSync IQ Installation & Operation Manual for
detailed instructions.
(C)
C
4 ft
minimum
TX Ant signal
out to clocks
SITESYNC IQ
B
A
To local
power
(110vac)
MON MAR 10 2014
10:38:06 AM USCT
American Time
Status=AUTO
GPS=Y
WIRELESS CLOCK SYSTEM
®
5
Use the Setup Wizard
1. Press 1 to start the Setup Wizard (Page 9 in Installation Manual)
2. Create a 4 digit User Lock or enter 0000 to disable this
feature. Press O.
Tip: Record this password.
3. Create a 4 digit Service Lock (for advanced features) or enter 0000
to disable this feature. Press O.
Tip: Record this password.
4. Select local time zone by using the <> keys. Press O.
Set Menu LOCAL
Time Zone Code:
05
99=Custom
USCT
<>=Scroll
OK=Accept
USET=Eastern USCT=Central USMT=Mountain USPT=Pacific
Note: There are 40 options to choose from
(Appendix B in Installation Manual)
8
5. Press
to select automatic DST (Daylight Saving Time) or
0
to disable DST if your location doesn't observe DST. Press
1
6. Press
for 12-hour mode - AM/PM (1:00PM).
2
Press
for 24-hour mode - Military (13:00).
7. Use the keypad to enter the Unit IP address. This is a static
address assigned by your Network Administrator. Enter preceding
O
zeros as necessary. Press
.
8. Use the keypad to enter the Time Server address. Enter preceding
O
zeros as necessary. Press
.
O
OR Press
to accept the default set at the factory.
9. Use the keypad to enter the Subnet Mask. This is the subnet mask
for your network. Enter preceding zeros as necessary. Press
10. Use the keypad to enter the Gateway IP. This is the IP address of
your network's Gateway device. Enter preceding zeros as
O
necessary. Press
.
11. The unit will prompt you to enter the Port Number. This is used for
remote web access and should be set to 0080. Press
the default (80) set at the factory.
8
7. To confirm proper set up, press
to sync.
• If successful, "Ethernet Sync Successful" will display
• If not successful, "Ethernet Sync Failed" will display. Re-try by
8
pressing
again.
8. "Setup Wizard Successfully Completed" will display.
The system controller now shows the correct time and date. You will no
longer be prompted on power-up for setup information.
9. Verify the unit is transmitting. TX should display for about three
seconds every 30 seconds (approximately the top and bottom of
every minute) in the bottom right corner of the screen.
MON
MAR
10
2014
10:38:06 AM
USCT
American Time
Status=AUTO
.
O
Note: Screen will
advance immediately
O
.
O
to accept
TX
Halaman Cetak