DoorHan PHOTO-W Panduan Instalasi - Halaman 2

Jelajahi secara online atau unduh pdf Panduan Instalasi untuk Pembuka Gerbang DoorHan PHOTO-W. DoorHan PHOTO-W 2 halaman.

Halaman Cetak

Ec DEclArATIOn OF cOnFOrMITY

We: DoorHan Europe s.r.o.

Bozeny Nemcove 1689, 43201 Kadan, Ceska Respublika

Herewith declare under sole responsibility that:

The active optoelectronic safety device model PHOTO - R

• Declares that:

The active optoelectronic safety device model PHOTO - R

• complies with the essential safety requirements of the following directives :

73/23/EEC and subsequent amendment 93/68/EEC

89/336/EEC and subsequent amendment 92/31/EEC and 93/68/EEC

Additional note:

These products have undergone tests in a typical uniform configuration (all

products manufactured by DoorHan Europe s.r.o.)

01/03/2010

Date signature

1. DEscrIPTIOn

Photoelectric detector Photo - W is a safety device, consisting of infrared

transmitter and receiver, which are installed in a gate opening. If an infrared

beam is interrupted, the control board receives the signal of an obstacle in a

dangerous area of an automatic system operation, and a system reacts as it

was preset by the operation logic - stop or reverse of gates.

2. IMPOrTAnT nOTIcE

• Warning! In order to ensure personal safety, it is important that all in-

structions be carried out to the letter. Incorrect installation or use of prod-

uct could cause serious personal injury.

• Before attempting installation, read the instructions carefully and store

in a safe place for future reference.

Appendix

range

Frequency

Voltage

Wave length

Input

Battery

Angle tolerance

Operating temperature

relay output

Dimension

Output way

*25 m supposed for stable work the distance can be reduced by 30% with bad

weather conditions: fog, rain, dust, etc.

Avoid ultraviolet beams!

3. InsTAllATIOn

Installation at height more than 20 sm, but not more 2 m. The first instal

and connects the receiver, after the TX is connected. Move a TX in the field

of installation while photo cells do not become parallel each other. In this case

the indicator LED3 of the receiver will evenly light up. Installation is completed.

notes

1. When the distance between the photocells is less than 5 meters, then it is

necessary to remove the jumper JP1 on the transmitter.

2. You should remove a battery, if the transmitter is connected by means

of wires.

Attention! From for features of distribution of infra-red radiation incor-

rect system operation is possible at small distance between a transmitter and

the receiver. The distance between them should be not less than 1 m. If sensi-

tivity of the receiver at small distance between a transmitter and the receiver

is insufficient, remove a receiver lens to increase its sensitivity.

4. cOnnEcTIOns

Select a necessary operating mode of photo cells concerning controlling

contacts: NO (it is normal opened) or NC (normally closed). If necessary

change position of crosspiece NC/NO.

1. You should switch DIP 1 on SW1 of the transmitter into ON or OFF posi-

tion, and you should switch DIP2 on SW1 into OFF position. When supply volt-

age is connected, LED3 will light up one time per second, and the transmitter

will send a signal.

2. You should switch DIP 1 on SW1 of the transmitter into ON or OFF po-

sition, and you should switch DIP2 on SW1 into ON position. When supply

voltage is connected, LED3 will be switched off, and the transmitter will not

send any signals.

The given logic is selected, when it is necessary to deactivate functioning

of the photocells.

SW1

DIP2

DIP1

LED3

CON2

VCC

(+24)

GND

InsTAllATIOn

MAnUAl

PHOTO – W

Mikhail Kiselev

12m-20m, the distance can be reduced by 30% with bad

weather conditions: fog, rain, dust, etc.

Lers

LED Indicator

NO/NC Jumper

Operating

output

Power supply 24 V AC/DC

Managing Director

2.5 KHz

12V-24V, DC/AC

940mm

Input

3 В, CR 123 A

<+/-5

-20C ~ 70C

150mA, max. 27V

37.5x108x3 6mm

NO/NC