DoorHan Sectional-1200 Panduan Instalasi dan Pengoperasian - Halaman 3
Jelajahi secara online atau unduh pdf Panduan Instalasi dan Pengoperasian untuk Pembuka Gerbang DoorHan Sectional-1200. DoorHan Sectional-1200 16 halaman.
Halaman Cetak
This manual is for operators DOORHAN SECTIONAL
automatic system seCtIonal is intended for use with residential
balanced gate (moderate use).
the system consists of an electromechanical motor-reducer, an
electronic control unit and a light lamp, located in common case. this
system is secured to ceiling and opens automatic gate by motion of chain.
the system serves as lock when the gate is closed, but in case of power
cut, the system can be released from inside or from outside and you can
open the gate manually.
the operator has compulsory built-in protection to prevent
entrapment.
the operator can be equipped with optional electronic safety sensors,
which stop gate closing in case of an obstruction or people in automatic
system coverage area.
automatic system seCtIonal is specially designed only for automatic
control of sectional gate, do not use the system for other purposes.
GENERAL SAFETY INSTRUCTIONS ON ITEM INSTALLATION
For safe operation of automatic gates do follow installation instructions contained in this manual.
•
Improper installation can cause injury to people and damage to their property.
•
read carefully this manual before installation.
•
do not make any changes in the automatic system, which are not specified in this manual.
•
operator seCtIonal is intended for automation of sectional gates. do not use the operator for other than intended purposes.
•
For fastening of the item, use hardware from operator kit or other analogous one.
•
Check for conformity of the gates to the standards en 12604 and en 12605 (see documentation for gates). For countries, which are
not eC members, the said measures are to follow in order to ensure standard safety level.
•
make sure, that the gate is well-balanced, runs smoothly and is equipped with mechanical end stops.
•
If the drive is not to be used with doors having openings exceeding 10 mm in diameter or having edges or protruding parts a person
could grip or stand on.
•
WarnIng: Important safety instructions. It is important for the safety of persons to follow all instructions. save these instructions.
During installation:
•
use the tools, showed in section "tools" of this manual.
•
When performing operation at a height, use stable support.
•
When drilling the holes, use protection for hands and eyes.
•
do not let children play during automatic opening of the gate.
•
Check before starting the automatic system, that there is no obstruction in the automatic system coverage area.
•
Before automatic opening of the gate, make sure, that the mechanical lock is open.
•
If required, install the manual external release t a height about 180 cm.
•
Install external control devices at a height not less than 150 cm, out of the automatic system coverage area, within visibility range.
•
maximal operator installation height is 450 cm. It is forbidden to install the operator at a height exceeding 450 cm. In case of
installation at a height exceeding 250 cm, it is necessary to observe the rules of work at heights!
After installation is completed:
•
Check safety sensors triggering at a height of 50 cm (if any obstruction within their coverage is detected or after touch with an
obstruction, the gate will stop automatically or will open) and actuation of protection by force exceeding 20 kg.
•
use the automatic system seCtIonal, following instructions from operating manual.
•
regularly have marks in servicing form done.
•
the automatic system seCtIonal does not require any special servicing.
IMPORTANT! RISK OF DAMAGE.
In case of supply cable damage, use the suitable type of the cable. replacement of the cable shall be done by qualified personnel at the
service centre.
3
I n s t a l l a t I o n a n d o p e r a t I n g m a n u a l s e C t I o n a l - 7 5 0 / 1 2 0 0
KIT COMPOSITION
№
name
1
operator
2
radio control button
3
Curved bar
4
supporting bracket
5
u-shaped bracket
6
Front bracket
7
Bracket for bar fastening
8
operator shaft adapter
9
guide assembly
10
Fastening elements
InTenDeD Use
1
Quantity
1
1
1
1
3
1
1
1
1
set
3