DoorHan SHAFT-50 Panduan Instalasi dan Pengoperasian - Halaman 4
Jelajahi secara online atau unduh pdf Panduan Instalasi dan Pengoperasian untuk Pembuka Gerbang DoorHan SHAFT-50. DoorHan SHAFT-50 12 halaman.
Juga untuk DoorHan SHAFT-50: Panduan Instalasi (12 halaman)
Halaman Cetak
2. SAFETY INSTRUCTIONS
WARNING! IMPORTANT SAFETY INSTRUCTIONS. Follow all instructions since incorrect installation can lead to severe injury.
Follow all instructions since incorrect installation can lead to severe injury.
Shaft-50 was designed for automation of industrial sectional doors. Do not use the operator for other than intended purposes.
DoorHan shall not be held responsible in case of injury caused by misuse of the product.
Prior to installation make sure that the door is properly balanced and moves smoothly.
Installation must be performed in accordance with the standards EN12453 and EN 12445. For countries, which are not EC members,
these requirements are to be met.
Check if the door conforms to the standards EN12604 and EN 12605 (see documentation accompanying the door). For countries,
which are not EC members, the above mentioned requirements shall be met in order to obtain an appropriate safety level.
Mechanical units of the door shall conform to the standards EN12604 and EN 12605.
Prior to installation, check that the location of operator installation is suitable by its climatic conditions to technical specifications of
the operator.
Do not install the operator in premises containing quick inflammable substances or other dangerous environments as it can cause
explosion or fire.
During assembly, installation and adjustment use tools specified in section "Tools" of this manual.
When performing operation at height, use a stable support.
When drilling holes, use protection for hands and eyes.
For fastening of the item, use hardware supplied with the operator or other analogous one.
Disconnect the supply when cleaning or other maintenance is being carried out, if the appliance is automatically controlled.
If the operator is installed on the door with a wicket door an additional safety device should be used to prevent operator activation
when the wicket door is open.
Ensure that entrapment between the driven part and the surrounding fixed parts due to the opening movement of the driven part is
avoided.
It is highly recommended to use DoorHan optional equipment as the accessories produced by other manufacturers can damage the
automated system.
DoorHan is not responsible for unstable work of the automatic system when using safety devices and accessories, which are produced
by other manufactures without agreement with DoorHan.
Never leave the electric motors in released condition. This may cause uncontrolled movement of the door leaves and, consequently,
their breakdown.
Do not use the operator if it needs repair or adjustment as installation defects or unbalanced door can cause injury.
DoorHan shall not be held liable in case of improper installation of the item and damage arisen during operation.
Since the operator does not have a power cord with a plug it shall be connected to the mains supply via automatic switch with a
minimal distance of 3 mm between the neighboring contacts. It is recommended to use a 10А double-
ole circuitbreaker.
Be sure there are no obstructions to door travel.
Do not make any changes in the automatic system not specified in this manual.
Remove package of the item and dispose of it. Keep the package materials away from children.
Always keep remote controls out of reach of children. Never permit children to operate or play with garage door control push buttons
or remote controls.
No one should cross the pass of the moving door.
This appliance can be used by children aged from 8 years and above and persons with reduced physi-cal, sensory or mental capabilities
or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way
and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by
children without su-pervision.
Permanently fix the label concerning the manual release adjacent to its actuating member.
Approach without the safety devices is allowed control mode driven by holding the button.
The content of the manual shall not be basis for any claim.
The manufacturer reserves the right to modify the design of the product described in this manual without preliminary notice.
The Installation and configuration of the actuator must only be carried out by qualified specialists.
After installing the drive, test force according to standards EN 12445 and EN 12453.
WARNING! For safe and correct operation of the operator put a stopper to limit door travel.
WARNING! RISK OF INJURY!
Have a qualified technician lay the cables 220–240 V AC. The cables must be laid in protective corrugated tubes. Avoid contact of
cables and moving parts of the door. In case of supply cable damage, use the suitable type of the cable.
Cables needed for installation of shaft-30 and accessories (if available):
Cable 2 × 0.5 mm
(photocell transmitter, stepped control button);
2
Cabel 4 × 0.5 mm
(photocell receiver);
2
Cable 3 × 1.5 mm
(power supply).
2
The cables should be appropriately insulated.
4
SAFETY INSTRUCTIONS