DoorHan SLIDING-2100 Panduan Instalasi dan Pengoperasian - Halaman 4
Jelajahi secara online atau unduh pdf Panduan Instalasi dan Pengoperasian untuk Pembuka Pintu Garasi DoorHan SLIDING-2100. DoorHan SLIDING-2100 12 halaman. Drive
Juga untuk DoorHan SLIDING-2100: Panduan Instalasi dan Pengoperasian (16 halaman), Panduan Instalasi dan Pengoperasian (12 halaman)
Halaman Cetak
WARnInGs FoR tHe InstALLeR
4. WARNINGS FOR THE INSTALLER
ATTENTION! to ensure the safety of people, it is important that you read all the following instructions. Incorrect installa-
tion or incorrect use of the product could cause serious harm to people.
Carefully read the instructions before beginning to install the product.
1.
do not leave packing materials (plastic, polystyrene, etc.) within reach of children as such materials are potential
sources of danger.
2.
store these instructions for future reference.
3.
this product was designed and built strictly for the use indicated in this documentation. any other use, not expressly
indicated here, could compromise the good condition/operation of the product and/or be a source of danger.
4.
doorHan declines all liability caused by improper use or use other than that for which the automated system was
intended.
5.
do not install the equipment in an explosive atmosphere: the presence of inflammable gas or fumes is a serious
danger to safety.
6.
the mechanical parts must conform to the provisions of standards en 12604 and en 12605. For non-eu countries,
to obtain an adequate level of safety, the standards mentioned above must be observed, in addition to national legal
regulations.
7.
doorHan is not responsible for failure to observe good technique in the construction of the closing elements to be
motorised, or for any deformation that may occur during use.
8.
the installation must conform to standards en 12453 and en 12445. For non-eu countries, to obtain an adequate
level of safety, the standards mentioned above must be observed, in addition to national legal regulations.
9.
Before attempting any job on the system, cut out electrical power.
10.
the mains power supply of the automated system must be fitted with an all pole switch with contact opening distance
of 3mm or greater. use of a 6a thermal breaker with all-pole circuit break is recommended.
11.
Make sure that a differential switch with threshold of 0.03 a is fitted upstream of the system.
12.
Make sure that the earthing system is perfectly constructed, and connect metal parts of the means of the closure to it.
13.
the safety devices (en 12978 standard) protect any danger areas against mechanical movement risks, such as
crushing, dragging, and shearing.
14.
use of at least one indicator-light (e.g. laMp ) is recommended for every system, as well as a warning sign ad-
equately secured to the frame structure.
15.
doorHan declines all liability as concerns safety and efficient operation of the automated system, if system compo-
nents not produced by doorHan are used.
16.
For maintenance, strictly use original parts by doorHan.
17.
do not in any way modify the components of the automated system.
18.
the installer shall supply all information concerning manual operation of the system in case of an emergency, and
shall hand over to the user the warnings handbook supplied with the product.
19.
do not allow children or adults to stay near the product while it is operating.
20.
Keep remote controls or other pulse generators away from children, to prevent the automated system from being
activated involuntarily.
21.
transit through the leaves is allowed only when the gate is fully open.
22.
the user must not attempt any kind of repair or direct action whatever and contact qualified personnel only.
23.
Maintenance: check at least every 6 months the efficiency of the system, particularly the efficiency of the safety
devices (including, where foreseen, the operator thrust force) and of the release devices.
24.
anything not expressly specified in these instructions is not permitted.
5. FUNCTIONS
these instructions apply to the following models: operators slIdIng
the slIdIng autoMatIon sYsteM for sliding gates comprises electromechanical operator which drive the gate by
means of tooth gear-rack. the system locks mechanically; therefore no electric lock is required.
to obtain anti-crushing protection, you have to use electronic control units with a torque control electronic device.
the slIdIng automation was designed and manufactured to control access of vehicles.
avoid any other use whatever.
4
I n s t a l l a t I o n a n d o p e r a t I n g M a n u a l o p e r a t o r s l I d I n g - 1 3 0 0 / 2 1 0 0