Astralpool MAX 1 Panduan Petunjuk Pengoperasian - Halaman 7
Jelajahi secara online atau unduh pdf Panduan Petunjuk Pengoperasian untuk Penyedot Debu Kolam Renang Astralpool MAX 1. Astralpool MAX 1 17 halaman.
Halaman Cetak
ENGLISH
Dear Customer,
Thank you for choosing our product to clean your pool. We hope that you will enjoy using your new robot to maintain your swimming pool for years to come.
Before you begin to use your robot, please take a few minutes to carefully read these operating instructions.
Again, thank you for choosing our product.
IMPORTANT SAFETY INSTRUCTIONS
READ AND FOLLOW ALL THE INSTRUCTIONS
CAUTION: Do not plug the power supply into a grounded outlet or do not switch the
pool cleaner "ON" if it is not fully immersed in water. Operating the cleaner out of water
will cause severe damage immediately and will result in loss of warranty.
Allow the cleaner to remain in the pool for 15 to 20 minutes following the end of its
cleaning cycle. This will allow the motors to cool adequately. Do not leave the cleaner
in the pool all the time. Always remember to turn the power supply "OFF" and unplug it
from the power outlet before removing the cleaner from the pool.
WARNING: The cleaner must not be used when people are in the water. For use
with swimming pool only
Safety Note
- The unit must be supplied through a residual current device (RCD) having a rated
residual operating current not exceeding 30 mA
- The connection to the branch circuit should be consistent with the local and national
wiring rules (electrical code).
- If the supply cord is damaged, it must be replaced by the manufacturer's service
agent or a qualified and trained person in order to avoid hazards.
This appliance is not intended for use by persons (including children)
with reduced physical, sensory or mental capabilities, or lack of
experience and knowledge, unless they have been given supervision or
instruction concerning use of the appliance by a person responsible for
their safety. Children should be supervised to ensure that they do not
play with the appliance.
WARNING: A Ground Fault Current Interrupter (GFCI-USA) or a Residual Current
Device (RCD-EUROPE) must be installed to protect your electric outlet and prevent
any possible electric shock.
IMPORTANT:
Please be sure to always keep your pool cleaner properly stored anywhere
between 10 to 40 degrees Celsius (50 to 104 degrees Fahrenheit). This will
keep the motors, plastics and seals protected. Failure to comply will result in
loss of warranty.
Robot can be used in water with temperatures ranging from 13°C to 35°C (55°F
to 95°F). However, the recommended optimal temperature is between 22°C
and 32°C (72°F and 90°F)
SAVE THESE INSTRUCTIONS
TROUBLESHOOTING
Moves slowly or doesn't seem to be vacuuming
This is the most common question. The solution is to make sure
that the filter bag is thoroughly clean.
Check to see that the suction ports are not clogged or blocked.
All LED lights are blinking on the power supply
Check to see if the unit is out of water.
Check to see if the propeller is stuck.
To restart, press the power button once. Cleaning program will
resume from it left off.
The Floating Cable is coiled up
Change the axle set-up. Unit is most likely turning too sharply.
Use the E-Z Swivel to straighten out the cable.
Unit is not sucking up debris
Check to see that you've properly set-up the unit and power
supply.
Check to see if the propeller is stuck.
Make sure the filter bag is clean.
Unit is stuck in the middle of the pool but the unit still
pumps out water
Check to see that there is nothing obstructing the cleaner or that
the cleaner is not stuck on any loose objects in the pool.
Unit looks like it is moving in the same area of the pool and
does not clean other areas
Change the axle set up by adjusting the pin configuration. This
will help move the cleaner in a different direction to clean.
Check your pin configuration.
Unit does not cover the entire pool
Check to see that the filter bag is thoroughly clean.
Adjust the timing cycle on the power supply.
Check to see that the axle area is not clogged.
Check your pin configuration.