Astria Fireplaces H8707 Petunjuk Instalasi

Jelajahi secara online atau unduh pdf Petunjuk Instalasi untuk Perapian Dalam Ruangan Astria Fireplaces H8707. Astria Fireplaces H8707 2 halaman. Kits for use with envy series direct-vent gas fireplaces

Halaman Cetak

INSTALLATION INSTRUCTIONS FOR LOG KITS

FOR USE WITH ENVY SERIES DIRECT-VENT GAS FIREPLACES

[FIREPLACE MODELS ENVY35TEN, ENVY40TEN, AND ENVY45TEN]

HOT GLASS WILL CAUSE BURNS.

DO NOT TOUCH GLASS UNTIL COOLED.

NEVER ALLOW CHILDREN TO TOUCH GLASS.

• Install only when fireplace is OFF and COLD.

• Fireplace surfaces get EXTREMELY HOT!

• The glass on the front of the fireplace reaches EXTREMELY HIGH

temperatures and can cause severe burns if touched. Even after the

gas is turned off, fireplace surfaces remain extremely hot.

• Keep children away from an operating fireplace. Closely supervise children in

any room where a fireplace is operating to prevent contact with glass.

f i r e - p a r t s . c o m

RISK OF PERSONAL INJURY OR PROPERTY DAMAGE.

• Do NOT abuse glass doors by striking or slamming shut.

• Never operate fireplace with glass door assembly removed.

• Handle glass door assembly with extreme care. Replace

damaged glass door assembly with approved replacement

assembly only.

• Use only media approved for use with these fireplaces (as

applicable). Failure to use approved media may result in sooting,

delayed ignition, or other improper fireplace operation, and may

void the warranty.

NOTICE

• READ ALL STEPS BEFORE STARTING INSTALLATION.

• LEAVE THESE INSTRUCTIONS WITH THE APPLIANCE.

• All warnings, precautions, and instructions in the Installation

Instructions and Care and Operation Instructions provided with the

appliance also apply to these instructions.

• If you encounter any problems, need clarification of these

instructions, or are not qualified to properly install this kit, contact

your local distributor or dealer.

GENERAL INFORMATION

This document contains installation instructions for the fireplace

log kit used with Envy direct‑vent gas fireplaces. This procedure

should be followed during initial appliance setup and when

re‑installing the log set after the annual cleaning and inspection

cycles.

Use care to prevent breakage when handling the logs. Once

heated by the fireplace, these logs are very fragile.

DO NOT install the logs until the appliance installation has been

completed, the gas line has been connected and tested for leaks,

and the initial burner operation has been verified.

NOTE: Turn OFF the appliance and allow it to completely cool

berfore installing this kit.

P/N 900005-04

Rev. A 10/2014

WARNING

CAUTION

NOTE: DIAGRAMS AND ILLUSTRATIONS NOT TO SCALE

P900005-04

FOR TRADITIONAL DIRECT VENT GAS FIREPLACES

REQUIRED TOOLS

• Safety Glasses

• Protective Work Gloves

KIT CONTENTS

1. Rear Log

2. Bottom Left Log

3. Bottom Right Log

4. Front Log

Figure 1: Log Set

Catalog number for the entire set:

35 in.—H8707,

40 in.—H8708,

45 in.—H8824

INSTALL ONLY WHEN FIREPLACE IS OFF AND COLD!

FIREBOX ACCESS

1. Use the fireplace remote control to ensure the fireplace is OFF.

2. Remove the top louver.

3. Remove the left and right side finish trim gap fillers.

4. Remove the surround trim assembly by detaching it at the

top of the fireplace and lifting it 1 in. to disengage the side

tabs, then pulling it away from the fireplace exposing the

front glass door.

5. Locate the four (4) spring‑loaded latches; two above and two

below the enclosure. Release the lower latches, by pulling

each handle out and down to unhook it from the glass door.

Lightly press against the door, to hold it in position, while

releasing the two upper latches. Carefully grip the glass door

at both the top and bottom, and remove from the fireplace.

Retain the door in a secure location for later reinstallation.

HEARTH PRODUCTS

KITS AND ACCESSORIES

LOG PLACEMENT GUIDE

NOTE: Envy log

placement is highly

sensitive. Follow

directions carefully.

5. Top Right Log

6. Top Left Log

• Log Placement Guide

CAUTION