Astria Fireplaces Rhapsody42 Series Panduan Petunjuk Instalasi - Halaman 4

Jelajahi secara online atau unduh pdf Panduan Petunjuk Instalasi untuk Aksesori Perapian Astria Fireplaces Rhapsody42 Series. Astria Fireplaces Rhapsody42 Series 12 halaman. Linear direct-vent fireplaces accessory kits

Halaman Cetak

Control Compartment

Access Panel and

Gasket

Right Burner Bracket

Figure 7 - Accessing the control compartment

3. Loosen the front left screw of the right burner bracket. Remove

the other three screws, and rotate the bracket clockwise to

uncover the slot in the ﬁ rebox ﬂ oor

Connect wiring harnesses for blower and optional

ﬁ rebox panel backlight kit - PF1 System*

NOTE: Use only original, factory-supplied wiring inside ﬁ replace.

1. In the control compartment, use a screwdriver or other

f i r e - p a r t s . c o m

blunt object to carefully break the sealant around the wires.

NOTE: Be careful not to damage the wires.

2. Plug the multiwire harness (provided with the ﬁ rebox panel

backlight kit) into the SimFlame™ (ﬂ icker) module port with

the red wires (Figure 8).

NOTE: If not installing the SimFlame module, plug the

multiwire harness directly into the power harness (omit the

components outlined in Figure 8) and skip step 3.

Multiwire Harness from

Panel Backlighting Kit

Figure 8 - Connecting multiwire harness and ﬂ icker module

3. Plug the power harness (provided with the ﬁ rebox panel

backlight kit) into the SimFlame Module port with the black

(Figure 9).

and white wires

Plug blower

into FAN port

Figure 9 - Connecting the lights and blower

INNOVATIVE HEARTH PRODUCTS • LINEAR GAS FIREPLACES • REQUIRED AND OPTIONAL ACCESSORIES

Oriﬁ ce

(Figure 7).

SimFlame

Module

If not using SimFlame

(flicker) module, omit

outlined components.

Slot

AUX

FAN

SimFlame

OUT

Module

Fan Control

Module

Plug lights into

AUX OUT port

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.

4. Route the lighting wiring up through the access opening, and

slide it into the slot

5. Plug the power plug end of the power harness into the AUX

OUT port on the ﬁ replace fan control module

Install reﬂ ector (from optional ﬁ rebox panel backlight kit)

1. Insert the bottom edge of the reﬂ ector (provided with the

ﬁ rebox backlight kit) into the ﬁ replace ﬁ rst. Then, push the

top edge into rear of ﬁ replace (Figure 10).

NOTE: Lift the reﬂ ector over the tabs on the rear ledge of the

ﬁ replace

2. Align the large hole in the lower face of the reﬂ ector over the

screw in the ﬁ rebox rear wall.

3. Align the screw holes in the top and bottom edges of reﬂ ector

with the rear most holes in the ﬁ replace ceiling and rear ledge.

Slot

Secure the reﬂ ector using six (6) #10-16 x 3/8 hex-head sheet

metal screws provided with the ﬁ rebox panel backlight kit.

Fireplace

Front

Figure 10 - Installing the reﬂ ector

Power

Harness

Install side panels (from required ﬁ rebox panel kit)

1. Align the screw hole in the top ﬂ ange of the side panel with

(Plug into

the upper hole in the inside wall of the ﬁ replace (Figure 11).

AUX OUT

2. Align the screw holes in the bottom ﬂ anges of the side

on Control

Module)

panel with the holes in the front and rear ledges.

3. Secure each panel with three (3) #10-16 x 3/8 hex-head

sheet metal screws provided with the ﬁ rebox panel kit.

Left Side

Panel

Figure 11 - Installing the side panels

*For PF2 System, see Page 5 and Figure 12.

(Figure 9).

Reﬂ ector

Tab

Rear Ledge

Left Side

Panel

Right

Side

Panel

Front

Ledge

(Figure 9).

Rear

Ledge