Dorma EM 3000-EW AH Panduan Instalasi - Halaman 3

Jelajahi secara online atau unduh pdf Panduan Instalasi untuk Kunci Dorma EM 3000-EW AH. Dorma EM 3000-EW AH 9 halaman. Early warning electromagnetic lock

Halaman Cetak

The EM 3000-EW AH supports 5 different building codes as below:

1. STANDARD BUILDING CODE

NUISANCE DELAY: Not allowed.

RELEASE DELAY: 15 sec. or ext. to 30 sec. with local approval.

RELOCKING: To be done upon door OPENS and CLOSES, using a doorswitch rather than a

keyswitch. Please connect NORMAL OPEN doorswitch to system Reset Switch Input.

2. NFPA 101

NUISANCE DELAY: Permitted up to 3 sec.

RELEASE DELAY: 15 sec. or ext. to 30 sec. with local approval.

RELOCKING: To be done manually by a keyswitch, a doorswitch cannot be used for relocking.

Please connect a momentary spring loaded NORMAL CLOSE keyswitch to system Reset

Switch Input.

3. UNIFORM BUILDING CODE

NUISANCE DELAY: Required to be set at 2 sec.

RELEASE DELAY: Required to be set at 15 sec.

RELOCKING: To be done manually by a keyswitch and must be located at the door, a

doorswitch cannot be used for relocking. Please connect a momentary spring loaded

NORMAL CLOSE keyswitch to system Reset Switch Input.

4. BOCA

NUISANCE DELAY : Required to be set at 1 sec.

RELEASE DELAY : 15 sec. or ext. to 30 sec. with local approval.

RELOCKING : Dip switch 4 must be in the OFF position to activate the relocking system after

the Release Delay expires, the door unlocks and opened, the doorswitch changes state and

remain open. When the door recloses, a relock delay of 30 sec. begins, if the door hasn't

been disturbed or open again during this 30 sec. it will relock, if it has been open again a 30

sec. relock will start all over again. The relock time count will not start till the door is closed.

5. NATIONAL BUILDING CODE OF CANADA

NUISANCE DELAY : Not allowed.

RELEASE DELAY : Required to be set at 15 sec.

RELOCKING : To be done manually by a keyswitch, a doorswitch cannot be used for

relocking. Please connect a momentary spring loaded NORMAL CLOSE keyswitch to system

Reset Switch Input.

DIP SWITCH SETTING FOR DELAY EGRESS FUNCTIONS

Factory setting : Nuisance Delay set at 3 sec. (Dip switch 2 OFF and Dip switch 3 OFF).

Factory setting : Release Delay at 15 sec. (Dip switch 1 ON).

Factory setting : Not BOCA. (Dip switch 4 ON).

O N

N u is a n c e D e la y

D ip S w it c h 2 & 3

2 3 4

0 S e c .

O N

R e le a s e D e la y

D ip S w itc h 1

1 2 3 4 5

1 5 S e c .

O N

B O C A S e t tin g

D ip S w itc h 4

1 2 3 4 5

N o n B O C A

C. EARLY WARNING ALARM FUNCTIONS

In the normal condition, the door is fail safe (power to lock) and locked, the local buzzer is off,

the Local Alarm Relay (DPDT, 1C) is deenergized and the Remote Alarm Relay (SPDT, 2C) is

energized.

The system will start the alarm sequences by just slightly pushing the door to enter the

Nuisance Delay Period which can be set for 0, 2, 4 or 6 seconds, at the same time the Local

Alarm Buzzer will sound pulsingly and the Local Alarm Relay will be energized, warning that

someone may force to open the secured lock, if that person wants to force to open the

secured lock, he or she must maintain pressure on the door until the end of the Nuisance

Delay Period and if he or she backs off before the time set, both the Local Alarm Buzzer and

the Local Alarm Relay will stop/be deenergized, and revert to normal operation. The purpose

of Nuisance Delay Period is to take the accidental triggering the sequence into consideration.

Once the Nuisance Delay Period time out, the Remote Alarm Period begins and can be set

for 0, 15, 30 seconds or infinity, at the same time the Remote Alarm Relay will be deenergized

and the Local Alarm Buzzer will go from pulsing to steady.

Once the Remote Alarm Period time out, both the Local Alarm Buzzer and the Local Alarm

Relay will stop/be deenergized. At the same time the Remote Alarm Relay will be energized.

Please note there will be no Remote Alarm period time out if the Remote Alarm Period is set

to infinity.

Once the Remote Alarm Period is time out, system will be reset to the normal condition when

the Reset Switch Input is CLOSE. That is, after reset, the system will start the alarm

sequences if someone pushes the door again. Please note system can be reset only after

Remote Alarm Period is time out. For infinity setting, reset is functional only after Remote

Alarm Period reaches 90 seconds.

O N

1 2 3 4 5

1 S e c .

2 S e c .

3 S e c .

O N

1 2 3 4 5

3 0 S e c .

O N

1 2 3 4 5

B O C A