Canyon 93-705 Petunjuk Perakitan - Halaman 3
Jelajahi secara online atau unduh pdf Petunjuk Perakitan untuk Perabotan Dalam Ruangan Canyon 93-705. Canyon 93-705 5 halaman. Charcoal collection student bunk bed
Halaman Cetak
STUDENT BUNK BED ASSEMBLY INSTRUCTIONS CONFIGURATION TYPE # 2
STUDENT BUNK BED ASSEMBLY INSTRUCTIONS CONFIGURATION TYPE # 2
LIST OF CONTENTS
CHARCOAL COLLECTION
TWIN UPPER BUNK BED BOX ( 92-705 ) FIG.1 ( 2 BOXES )
A.- (1) LOFT BED END
HARDWARE PACK (HPK00095)
B.- (2) METAL DOWEL PINS
3 DRW STUDENT LOFT DESK BOX ( 92-710 ) FIG.2
C.- (1) 3 DRW STUDENT LOFT DESK
5 DRW STUDENT LOFT CHEST BOX ( 92-711 ) FIG.3
D.- (1) 5 DRW STUDENT LOFT CHEST
6 PCS SIDE RAILS BOX ( 92-730 ) FIG.4
E.- (4) SIDE RAILS
F.- (2) GUARD RAILS
HARDWARE PACK (HPK00093)
G.- (24) 5/16" X 4" HEX TAP BOLTS
H.- (24) 5/8" CROSS DOWEL NUTS
I.- (24) 5/16" FLAT WASHERS
J.- (1) 5MM ALLEN WRENCH
LADDER BOX (92-720) FIG.5
K.- (1) LADDER
HARDWARE PACK (HPK00008)
L.- (2) METAL HOOK BRACKETS
M.- (6) 1" SCREWS
TWIN BED BOX ( 92-707 ) FIG.6
N.- (1) HEADBOARD
O.- (1) FOOTBOARD
HARDWARE PACK (HPK00094)
P.- (4) CASTER SOCKETS
4 PCS SLAT PACK 3/3 BOX ( 92-645 ) FIG.7 ( 2 BOXES )
Q.- (4) 39'' SLATS
HARDWARE PACK (HPK00016)
R.- (8) 1 1/4" SCREWS
TOOLS NEEDED
PHILLIPS HEADSCREWDRIVER ( NOT INCLUDED )
5MM ALLEN WRENCH ( INCLUDED )
1.- ASSEMBLE TWIN UPPER BUNK BED, USING TWO LOFT BED ENDS (A), TWO SIDE RAILS (E), AND TWO GUARDRAILS (F).
2.- INSERT TWO CROSS DOWEL NUTS (H) INTO THE SIDE RAIL AND GUARDRAILS HOLES, MAKE SURE THE GROOVE IS HORIZONTAL, SEE FIG.8
3.- ATTACH TWO SIDE RAILS (E) AND TWO GUARD RAILS (F) TO BOTH LOFT BED ENDS (A), INSERTING TWO HEX TAP BOLTS (G) TWO WASHERS (I) INTO LOFT BED
5MM ALLEN WRENCH (J) TO TIGHTEN BOTH HEX TAP BOLTS
4.- REPEAT THE SAME PROCESS ON ALL FOUR CORNERS.
5.- PLACE FOUR SLATS (Q) ON TOP SIDE RAIL CLEATS, ONE SLAT IN BOTH LOFT BED ENDS, PUSH THE SLAT AGAINST THE BED END POST ( FIG.A ) AND TWO SLATS IN THE MIDDLE AT
EQUAL DISTANCE FROM THE END SLATS, THEN EACH SLAT END MUST BE FASTEN WITH ONE 1 1/4" SCREW (R), SEE FIG.10
YES,
HORIZONTAL GROOVE
FIG.8
REV 01 14/04/2016
CANYON FURNITURE COMPANY
( DO NOT TIGHTEN COMPLETELY UNTIL ALL PIECES ARE CONNECTED TOGETHER )
NO
FIG.9
A
B
FIG.1
L
M
K
FIG.5
N
O
P
FIG.6
MAKE SURE ALL BOLTS ARE TIGHTENED
FIG.A
PAGE 3 OF 5
C
FIG.3
FIG.2
E
G
H
FIG.4
Q
FIG.7
COMPLETELY
, SEE FIG.9
D
F
J
I
R
END HOLES, USE THE
FIG.10
KIS01112