Dot-Spot clarios flex beam Panduan Operator - Halaman 13

Jelajahi secara online atau unduh pdf Panduan Operator untuk Sorotan Dot-Spot clarios flex beam. Dot-Spot clarios flex beam 15 halaman.

Halaman Cetak

Assembly

Setting the flex beam (clarios flex beam only)

Loosen the two grub screws M3 on the front ring of the luminary using the provided hex key of the

size 1.5. Attention: Do not completely unscrew grub screws due to the risk of loss. Rotating the bezel

and changing the beam angle:

■ Clockwise rotation (viewing direction with the light beam) narrows the beam angle.

■ Counterclockwise rotation (viewing direction with the light beam) increases the beam angle.

■ The narrowest and the widest point are several rotations apart from each other.

■ There is a limit stop at the narrowest and the widest point. Do not turn the bezel over those

points, otherwise the lens mechanism may be destroyed.

After adjustment, screw the grub screws finger-tight, in order to be on the safe side, only use the

short end of the key as lever.

Operation

LED lights are extremely energy efficient and, under normal operation, have a very long life. To

ensure the maximum life of the LED and to increase the energy efficiency, the following should be

considered:

■ The turning on and off of the luminary should be carried out by the input circuit of the power

supply.

■ The turning off of the luminary via the PWM signal should not occur permanently since in this

case the electronics unit of the luminary continues operating.

■ Even if the luminary is equipped with a THERMOPROTECT system that protects the luminary

against thermal damage, a permanent abnormal operation should be avoided.

■ The heat dissipation of the LED must not be hindered. Therefore, do not cover the spot.

■ Avoid operating the spot in case of direct solar radiation.

■ In automatic mode, control the spot via timer and / or twilight switch.

Maintenance, disposal

Care

■ Clean the spot with a damp cloth every now and then.

■ The luminaries are made of stainless V4A steel. However, depending on the environmental

conditions and the surfacing material, the metal parts may present the so-called flash rust, but

this does not constitute a defect. Flash rust can be removed easily with appropriate stainless

steel cleaners. Flash rust is particularly likely when the housing comes into contact with ferrous

particles (e.g. iron and grinding dust, ferrous plant fertilizers or the like).

Illuminants

LED lights, under normal operation, have a very long life. Therefore, the replacement of the lamp is

not provided. In case of questions, see the Service chapter.

Maintenance, disposal

Disposal

At the end of the useful life, dispose of the spot and all accessories in accordance with the appli-

cable environmental regulations. Electrical waste must not be disposed of with domestic waste.

Malfunction, failure detection and elimination

Malfunction

Cause

PWM line not connected

to ground or dimmer

PWM signal not present

M12 connector system non laid

out properly, wrong components

Spot does not work

Line leading to the power supply,

dimmer is interrupted

Supply voltage towards the pow-

er supply is interrupted

Power supply defective

Luminary is defective

Spot flashes, flickers or

switches off after a short

Power supply is overloaded

time of operation, the

power supply gets very hot

Operation at high housing tem-

The luminosity of the

peratures, the THERMOPROTECT

spot decreases during

system reduces the power until

operation or the spot

the spot switches off, in order to

does not work anymore

protect the LED

Warranty

These terms of warranty apply to the purchase and use of our products in the Federal Republic of

Germany. In other countries the warranty conditions will be those stipulated in the terms of sales

and shipment for the respective country or by law. The legal warranty rights are not affected by this

warranty. This warranty statement is our voluntary service as manufacturer.

All dot-spot products are 100% checked and tested before leaving the factory. However, the occur-

rence of occasional failures during operation may not be completely excluded.

In accordance with legal provisions, we grant a two-year warranty from the date of purchase (invoice

receipt). This warranty refers to the proper function of the dot-spot garden and object spots and

accessories under normal conditions of use.

Correction

check by connecting

the PWM wire to ground

Check dimmer

(PWM signal generator)

Check components of

the M12 connector system

Check cable,

replace if necessary

Check input voltage

at the power supply

Replace power supply

Send in luminary

Use power supply with higher

power output

Operation of the spot at low

ambient temperatures or with

better air circulation