Double K Industries Challengair 2000 Plus Buku Petunjuk - Halaman 2

Jelajahi secara online atau unduh pdf Buku Petunjuk untuk Produk Perawatan Hewan Peliharaan Double K Industries Challengair 2000 Plus. Double K Industries Challengair 2000 Plus 4 halaman. Dryer/vac for animals

Halaman Cetak

IMPORTANT SAFEGUARDS

WARNING: IMPORTANT SAFETY PRECAUTIONS! PLEASE READ
COMPLETELY BEFORE USING PRODUCT!
When using electrical appliances, especially in the presence of children or animals,
basic safety precautions should always be followed to reduce the risk of re, electric
shock, and personal injury, including but not limited to the following:
DO NOT TURN ON DRYER WITHOUT FIRST HOLDING THE DRYER HOSE, as the air
volume from the dryer can cause the hose to whip or move rapidly and may cause
injury.
1.
Do not leave dryer OR animal unattended while in use.
2.
Unplug unit when not in use.
3.
Do not use extension cords with dryer.
4.
Do not unplug unit by pulling on cord.
5.
Do not expose dryer to rain or water.
6.
Do not use or store dryer where it can fall or be pulled into tub, sink or standing
water. If dryer falls into water . . . UNPLUG IT . . . Do not reach into the water!
7.
Unplug unit before attempting any maintenance or service.
8.
Do not put any object into dryer openings.
9.
Keep loose clothing, jewelry and hair away from dryer intake.
10.
Do not direct dryer air towards eyes or ears of people or pets.
11.
Never use dryer if it has a damaged cord or plug, has been dropped, damaged
or exposed to rain or water. Return to Double K Industries or an Authorized
Service Center for service.
12.
When using the cage attachment, do not leave the animal unattended.
13.
This product is for use on animals only.
14.
Recommended operation by adults only. Use caution when working around
children.
15.
Do not use attachments not recommended by Double K Industries.
16.
Do not operate without lters in place. Keep lters clean, as dirty lters limit air
intake and may damage the motor or cause overheating.
17.
Only plug into a properly grounded receptacle. Always make sure the amper-
age of the electrical outlet is su cient for the amperage rating of the product.
(See Product Speci cations on front page for amperage rating of this product).
18.
Do not use product for anything other than its intended purpose.
19.
Do not attempt to perform any service or maintenance not outlined in instruc-
tion manual.
20.
Do not attempt any product modi cations or alterations. Do not use, if any
parts or switches are damaged. Send to an Authorized Service Center
or Double K Industries for service.
21.
When servicing, use only Double K Industries parts.
2
BRUSHES
Your CHALLENGAIR 2000PV™ has one brush-type motor. The brushes should be
checked for wear after approximately 600 hours of use. If the carbon brushes are
worn shorter than 1/4 inch, the brushes should be replaced. Brushes may be ordered
from Double K Industries or an Authorized Service Center. Please be sure to specify
that your dryer is a 2000PV™ , as the brushes are slightly di erent from one dryer
model to another.
To check and/or replace brushes:
1.
Unplug electrical cord from wall outlet.
Disassembly:
2.
Slide o the back cover from the dryer. This is a compression t and will come
o with a little e ort.
3.
Remove all screws on the outside of the dryer that hold the two halves of dryer
housing in place. Lay the dryer on its side while removing these screws. Remove
the O-ring on the snout of the dryer and lift the top half.
4.
Each motor will be sitting in place inside the rubber silicone motor mounts.
Removing the rubber silicone motor mounts from the motor is not neces-
sary to replace brushes. The internal lter frame ts into slots on the inside
of the dryer housing. This piece can remain while changing brushes.
5.
Disconnect motor power wires (see wiring diagram). Note where wires connect.
6.
Motor: (a) Find the ag connector on the top of the brush assembly. There is a
wire leading to this connector. (b) Place a athead screwdriver with a ne tip
between the ag connector and the plastic brush housing. (c) Rock the screw-
driver back and forth and gently wedge the ag connector out of the brush
assembly. (d) Loosen the two brush assembly retainer bracket screws.
(e) Remove the brush assembly. (f)Replace the brush assembly with the new
one, making sure that the small tab on the bottom is tted onto the corre-
sponding slot on the motor frame. (g) Replace the brush assembly retainer
bracket and tighten the screws which hold it in place. (h) Attach the ag
connector to the new brush in the same position as the previous brush.
(i) Repeat these steps for the brush on the other side of the motor.
Reassembly:
7.
Inspect the motor mount for cracks or damage -- replace if necessary.
Set the motor back into its original position in the dryer housing. The
motor mount has slots that t over corresponding alignment tabs on the
inside of the dryer housing. These slots and tabs must match up for proper
t and function. (Note: In the event that the motor mount is removed from
the motor, simply replace it by being mindful to align the contours of the
motor mount with corresponding contours on the motor housing.) Make
sure that the internal lter housing is in its appropriate slot before putting
the halves together.
8.
Reattach the screws around the outside of the dryer making sure the two
halves are matching up.
9.
After the two halves of the dryer housing have been put together, replace
internal lter and push the back cover onto the rear of the dryer. Always make
sure all lters are in place before operating dryer. Replace o-ring on snout.
7