Double K Industries Challengair 2000AD Panduan Memulai Cepat - Halaman 2
Jelajahi secara online atau unduh pdf Panduan Memulai Cepat untuk Produk Perawatan Hewan Peliharaan Double K Industries Challengair 2000AD. Double K Industries Challengair 2000AD 2 halaman. Animal dryer & vacuum
Halaman Cetak
has a two year limited warranty covering the unit against defects in materials and workmanship. See
warranty card for complete warranty information and exclusions.
Your Challengair 2000AD or 2000Plus has a brush type motor. It is important that the brushes be
changed when they become worn down to prevent damage to your dryer motor. We suggest checking the
motor brushes after every 600 hours of use. Please see section on "brush changing" in this manual for
instructions.
A note about dryer heat: Your Challengair 2000AD/2000Plus has no heating element. It produces heat
by a "flo-thru" motor system meaning the air is pushed through the motor and is warmed by the natural
heat of the motor that occurs during operation. This means greater temperature after about 2-4 minutes of
operation. Obviously, the greater the room temperature, the warmer the air from the dryer.
Assembly
To attach hose for drying: Insert the gray hose adapter on the end of the hose firmly into the air outlet
snout. (Rotating while pushing is helpful. This is a tight fit but it will go in. Running the nozzle under hot
water for about 30 seconds will soften it and make it easier to insert into the snout.)
For Challengair 2000Plus or 2000EV Vacuum models only:
To attach hose for vacuuming: Insert gray hose adapter into the hole in the back of the unit.
Attachments: Your dryer/vacuum is equipped with one hose, 3 twist on nozzles, one slip-on super
velocity nozzle, and one cage attachment. Vacuum models also include on claw nozzle and one crevice
tool. Equine vacuum models also include a curry vacuum brush.
Removing and attaching nozzles: All threaded nozzles are reverse thread and are attached directly to the
hose. Turn clockwise to remove, counterclockwise to attach. To attach super velocity nozzle, first attach
high velocity nozzle to hose and then slip the Super Velocity Nozzle onto the high velocity nozzle.
For Equine models only: To attach the curry vacuum brush to the hose for vacuuming, attach the high
velocity nozzle to the hose end and then slip the curry vacuum brush onto the high velocity nozzle.
Operation- Switches and Controls
1)
Single speed- Two position switch
Right Position- Off
Left Position- On
2)
Two Speed Unit- Three position switch:
Middle position-Off
Left Position- High
Right position- Low
Maintenance (all models)
Filter Cleaning: The motor filter of the unit must be kept clean. If it becomes heavily coated with hair and
debris, it could reduce both the dryer air and the vacuum suction. (Never run unit without filter in place.)
TO CLEAN FILTER: a) Unplug unit b) Remove the back cover from the motor by turning and pulling off. c)
On vacuum units- remove the vacuum bag. d) Remove the motor filter disk from the motor by turning and
pulling off. e) Clean motor filter disk by vacuuming off or wash filter in cool water. Shake off excess water
and allow to dry completely. f) Replace filter disk on motor by pushing in place. g) Replace the back cover
on the unit.
Cleaning Dryer Interior
Hair and dust will accumulate inside the dryer. Blow clean as needed using a Challengair Forced Air
Dryer or suitable high pressure air outlet.
Cleaning Vacuum bags (model 2000plus or 2000EV vacuum units only)
Remove the back cover from the vacuum. This is a compression fit and will pull off. Remove old vacuum
bag and dispose of in wastebasket. Install new bag and replace dryer back cover. To order replacement
vacuum bags, part #2075 (pkg of 5 bags) contact Double K Industries. Use only Double K replacement
vacuum bags in the Challengair 2000Plus
Motor Brushes
Your Challengair 2000AD/ 2000Plus has a brush-type motor. The brushes should be checked for
wear after every 600 hours of use. If the carbon-brush is worn shorter than ¼ of an inch, the brush should
be replaced. Brushes may be ordered from Double K Industries or an authorized service center.
To check and/or replace brushes:
1)
Unplug electrical cord from the wall outlet. 2) Remove the back cover from the unit. 3) Loosen
the four screws on the outside of the dryer that hold the motor in place. 4) Remove the motor
from the dryer housing. The brushes are now visible and accessible. 5) Remove tab from the
brush bracket assembly using a flat blade screwdriver to push out (fig.2) 6) Loosen and
remove the two screws in the brush bracket and remove both the bracket and the brush. 7)
Blow motor assembly clean using high pressure air. 8) Insert new brush assembly in place and
replace brush bracket over assembly, install tighten the two screws. 9) Insert the brush tab into
the new brush assembly. 10) Repeat for other side. 11) Slide the motor back into the dryer
housing. Align the screw channels and replace the four screws evenly and securely, but do not
over tighten. 12) Replace back plate.
Any maintenance not explained in this manual should be performed by Double K Industries. Call
Double K Industries for the name of the service center nearest you. All warranty service must be
performed by an authorized service center to protect your warranty status.